Author Topic: Weekend Update 2/10/19  (Read 3861 times)

0 Members and 1 Guest are viewing this topic.


Tom Todd

  • Crew
  • *
  • Posts: 62
  • Respect: +6
Re: Weekend Update 2/10/19
« Reply #1 on: February 08, 2019, 08:10:16 PM »
+1
That is a fun video!!  I really liked to last load of copper vessels.

Tom

cbroughton67

  • Crew
  • *
  • Posts: 375
  • Gender: Male
  • Respect: +1045
Re: Weekend Update 2/10/19
« Reply #2 on: February 08, 2019, 08:21:58 PM »
+5
After getting a dose of inspiration over on the DCC thread, I finished-up installing an ESU LokSound decoder in an Arnold SW-1 switcher this week. I went a step further by installing three SMD capacitors, which are sandwiched between the chassis and speaker enclosure. Wire grab irons and weathering finished it off.

Chris Broughton

"Clothes make the man. Naked people have little or no influence on society." - Mark Twain

Kentuckian

  • Crew
  • *
  • Posts: 420
  • Gender: Male
  • "This all started with Romans 10:9!" -Apologetix
  • Respect: +51
Re: Weekend Update 2/10/19
« Reply #3 on: February 08, 2019, 08:31:18 PM »
+1
Started hanging shelf tracks today. I finally got everything in fro Home Depot; last week’s winter storm messed up the order. Lots still left to do!

[ Guests cannot view attachments ]
Modeling the C&O in Eastern Kentucky.
C&O HS

Caleb Austin

  • Crew
  • *
  • Posts: 504
  • Gender: Male
  • Respect: +281
Re: Weekend Update 2/10/19
« Reply #4 on: February 08, 2019, 08:51:57 PM »
+17
I've been working on installing a road overpass and surrounding scenery on this curve. Got ground cover and ballast down this week.



Caleb.

hegstad1

  • Crew
  • *
  • Posts: 359
  • Respect: +468
Re: Weekend Update 2/10/19
« Reply #5 on: February 08, 2019, 09:42:24 PM »
+4
I've started doing a lot of drawing this week and have started doing some test cutting with the Silhouette Cameo 3.  I'm learning the possibilities and limitations and so far I'm excited.  I may have to start a thread in the scratch building forum.  Below are some screen shots of the Park Hotel and Carpenter Paper Company, both in Missoula.




Andrew Hegstad

cbroughton67

  • Crew
  • *
  • Posts: 375
  • Gender: Male
  • Respect: +1045
Re: Weekend Update 2/10/19
« Reply #6 on: February 08, 2019, 11:19:45 PM »
0
I've started doing a lot of drawing this week and have started doing some test cutting with the Silhouette Cameo 3.  I'm learning the possibilities and limitations and so far I'm excited.  I may have to start a thread in the scratch building forum.  Below are some screen shots of the Park Hotel and Carpenter Paper Company, both in Missoula.


@hegstad1 I've seen the Cameo cutters listed online, and I've been curious about them, their ease of use, and their capabilities. I hope you do start a thread and chronicle your experience with it. Sounds like it would be very informative!


Chris

Chris Broughton

"Clothes make the man. Naked people have little or no influence on society." - Mark Twain

PGE_Modeller

  • Crew
  • *
  • Posts: 279
  • Respect: +18
Re: Weekend Update 2/10/19
« Reply #7 on: February 09, 2019, 12:54:28 AM »
0

@hegstad1 I've seen the Cameo cutters listed online, and I've been curious about them, their ease of use, and their capabilities. I hope you do start a thread and chronicle your experience with it. Sounds like it would be very informative!


Chris

I would also like to see a thread on the Cameo cutter as I have acquired one but haven't put it to use yet.

Cheers,

peteski

  • Crew
  • *
  • Posts: 19766
  • Gender: Male
  • Respect: +1656
    • Coming (not so) soon...
--- Peteski de Snarkski
--- Honorary Resident Curmudgeon

hegstad1

  • Crew
  • *
  • Posts: 359
  • Respect: +468
Re: Weekend Update 2/10/19
« Reply #9 on: February 09, 2019, 05:22:27 AM »
0
Andrew Hegstad

Dave V

  • Global Moderator
  • Crew
  • *
  • Posts: 8402
  • Gender: Male
  • The Route of the Galloping Goose
  • Respect: +3058
    • Dave Vollmer's N Scale Pennsy
Re: Weekend Update 2/10/19
« Reply #10 on: February 09, 2019, 02:48:11 PM »
+13
Been working on Rico...






Silver San Juan Scenic Line

Member SlimRail Modular Colorado Narrow Gauge
http://www.slimrail.net/

sirenwerks

  • Crew
  • *
  • Posts: 5164
  • Gender: Male
  • Respect: +131
Re: Weekend Update 2/10/19
« Reply #11 on: February 09, 2019, 03:10:38 PM »
0
I've started doing a lot of drawing this week and have started doing some test cutting with the Silhouette Cameo 3.  I'm learning the possibilities and limitations and so far I'm excited.  I may have to start a thread in the scratch building forum.  Below are some screen shots of the Park Hotel and Carpenter Paper Company, both in Missoula.





Please do start a thread. I have one now four years old sitting in the box unopen, got it on sale just before the move west. I need to put it to use finally.
Now seeking Pacific NW N scalers to create a Modutrak-style modular club featuring NP's shared mainline between Seattle and Portland. PM me if interested.

trainforfun

  • Crew
  • *
  • Posts: 1657
  • Respect: +42
Re: Weekend Update 2/10/19
« Reply #12 on: February 09, 2019, 03:26:42 PM »
0
Trying to post and forget how to ......
Help !!!!!
« Last Edit: February 09, 2019, 03:29:21 PM by trainforfun »
Thanks ,
Louis



peteski

  • Crew
  • *
  • Posts: 19766
  • Gender: Male
  • Respect: +1656
    • Coming (not so) soon...
Re: Weekend Update 2/10/19
« Reply #13 on: February 09, 2019, 03:51:12 PM »
0

Please do start a thread. I have one now four years old sitting in the box unopen, got it on sale just before the move west. I need to put it to use finally.

I guess we need an 8th thread describing how Cameos work.  I suppose that everybody uses those machines differently.
--- Peteski de Snarkski
--- Honorary Resident Curmudgeon

mu26aeh

  • Crew
  • *
  • Posts: 2897
  • Gender: Male
  • Respect: +758
Re: Weekend Update 2/10/19
« Reply #14 on: February 09, 2019, 04:10:23 PM »
+1
What happens when I'm left at home alone too long



Bye bye Hagerstown yard.
« Last Edit: February 09, 2019, 04:13:51 PM by mu26aeh »