Author Topic: An N-Possible journal  (Read 41239 times)

0 Members and 1 Guest are viewing this topic.

Chris333

  • Crew
  • *
  • Posts: 19710
  • Respect: +6987
Re: An N-Possible journal
« Reply #495 on: October 21, 2026, 08:15:24 PM »
0
Are they still 3D printed or did they go into production?

robert3985

  • Crew
  • *
  • Posts: 3602
  • Respect: +2000
Re: An N-Possible journal
« Reply #496 on: October 21, 2026, 08:26:31 PM »
0
This is a canonical example of what in engineering circles would be referred to as a "kludge".

At essence, these serve to mask the problem, not solve it;  furthermore they introduce problems of their own, such as reduced effective engine power, increased tendency to stringline, or have compression derailments when pushing (esp thru tight curves or turnouts). It's more or less equivalent to moving cars with the brakes applied.

Ed

Fair enough...but I've found my BLI M1 (the latest release) can pull anything I ask of it, so additional rolling resistance may not be as bad as all that. But you're right...it's another example of a Band-Aid.

All this slinky talk has got me confused (I thought N-Possibles did away with the slink!).

Please tell me all this slinky talk has absolutely nothing to do with N-Possibles  :o (another extreme thread drift? :D)

Yup, Ed and Dave are right...axle springs are definitely a "Band-Aid" and have drawbacks.  However, for roundy-round operation (no backing thru #4 crossovers, no 100+ car trains stringlining on 11" radii) such as typical TTRAK curves, these lil' springs just might solve Dave's problem...and on the cheap too.

And, the ultimate "fix" for slinky-itis is N-Possibles, or even True Scale Couplers if yer not worried about coupling & uncoupling, such as a coal drag...AND, N-Possibles and True Scale Couplers are compatible.  Yup. 

The only thing that this "slinky talk" has to do with N-Possibles, is that they are the ultimate fix as well as the ultimate N-scale coupler, which only could have been achieved by being incompatible with any other MTL-style knuckle coupler.

Adapter cars are the "fix" to replacing everything with N-Possibles or True Scales.  Exactly the same strategy as when everybody was replacing Rapido-style couplers with Kadee N-scale couplers back in the day...except N-Possibles are way better in every aspect than MTL-style knuckle couplers AND better than True Scales (unless you absolutely are going to use Magnematic uncoupling).

Cheerio!
Bob Gilmore

GaryHinshaw

  • Global Moderator
  • Crew
  • *
  • Posts: 6800
  • Respect: +2669
Re: An N-Possible journal
« Reply #497 on: October 21, 2026, 09:42:55 PM »
+1
Are they still 3D printed or did they go into production?

Yes and yes.  3d printing = production.  (Okay, not everything is on the market yet, but they will be 3d printed when they are.)  The print quality is top notch!

Jimbo

  • Crew
  • *
  • Posts: 218
  • Respect: +97
Re: An N-Possible journal
« Reply #498 on: October 21, 2026, 09:51:46 PM »
0
How well do these couplers work in T-TRAK situations?

Dave,

A couple months ago, our club set up our T-Trak modules for “train day” at our local library.  I brought some of my equipment that I’ve converted to N-Possible couplers.

We ran for hours a train equipped exclusively with N-P couplers, and had NO issues whatsoever, despite the tight curves on the end caps. No slinky, no undesired uncoupling… my experience has been nothing but positive operations-wise.  I have learned a technique to uncouple using picks that works great.  Biggest drawbacks are cost and time investment needed to do installs.  And some of those installs are a pain in the rear end.

I model transition era, so for me the biggest selling point is appearance on the pilots of steam locomotives.  It makes a massive improvement.  But performance always trumps everything else, and they haven’t disappointed me.

(For what it’s worth… my equipment is mostly 40’ cars.  I can’t vouch for how long cars would perform on the tight radii on T-Trak endcaps, but let’s be honest… regardless of couplers, long cars look wrong on those!)

Hope this helps!

Jim

Jimbo

  • Crew
  • *
  • Posts: 218
  • Respect: +97
Re: An N-Possible journal
« Reply #499 on: October 21, 2026, 10:03:22 PM »
0
Yes and yes.  3d printing = production.  (Okay, not everything is on the market yet, but they will be 3d printed when they are.)  The print quality is top notch!
Maybe it’s just me… but the most recent bunch I received seemed even cleaner than the early ones.  Either he tweaked (and improved) the print or is doing a more precise job of trimming supports.  Regardless… I’m happy!

Jimbo

  • Crew
  • *
  • Posts: 218
  • Respect: +97
Re: An N-Possible journal
« Reply #500 on: October 21, 2026, 10:10:16 PM »
0
Must they only be body-mounted? And are they universally compatible with MTL and Accumate couplers?
Forgot to add…
He had samples of conversions for MT truck mounted couplers.  You disassemble the coupler, install an N-P coupler, and install a new lid.  He distributed samples last year in Kansas City.  Very easy.  I have no idea when (or if) these will reach production.

My experience also is that they will mate (not automatically though) with Kato couplers.  At least the ones on my passenger cars.  (Which basically means my conversions of these are low priority.)

Jim

Sokramiketes

  • Crew
  • *
  • Posts: 5427
  • Better modeling through peer pressure...
  • Respect: +2196
    • Modutrak
Re: An N-Possible journal
« Reply #501 on: October 21, 2026, 10:22:14 PM »
+1
Are they still 3D printed or did they go into production?

I assume by "production" you are asking if molded plastic would be better.  The answer is no.  With 3D printing that pulling face is dead flat, no draft angle.  That's part of why they grip so well on the edge case, where coupler heights are off.  Add in all the detail you get in whatever pocket and angle the prototypes had... and man, they almost have to be 3D printed. 

Sokramiketes

  • Crew
  • *
  • Posts: 5427
  • Better modeling through peer pressure...
  • Respect: +2196
    • Modutrak
Re: An N-Possible journal
« Reply #502 on: October 21, 2026, 10:24:26 PM »
0
Maybe it’s just me… but the most recent bunch I received seemed even cleaner than the early ones.  Either he tweaked (and improved) the print or is doing a more precise job of trimming supports.  Regardless… I’m happy!

For sure, and that's made assembly even faster.  I don't have to sand the new ones and the pencil lead lube is becoming somewhat optional too.  I don't understand the level of tenacity that Andrew has to keep tweaking these things down to the pixel in his printers, but I can admire it as a thing I don't have!

Chris333

  • Crew
  • *
  • Posts: 19710
  • Respect: +6987
Re: An N-Possible journal
« Reply #503 on: October 21, 2026, 10:41:55 PM »
+1
Oh I haven't been paying attention. I thought the idea was test in 3D and then do plastic. And I never saw plastic ones.

Carry on and 3D print the whole world.

Sokramiketes

  • Crew
  • *
  • Posts: 5427
  • Better modeling through peer pressure...
  • Respect: +2196
    • Modutrak
Re: An N-Possible journal
« Reply #504 on: October 21, 2026, 10:54:01 PM »
0
Oh I haven't been paying attention. I thought the idea was test in 3D and then do plastic. And I never saw plastic ones.

Carry on and 3D print the whole world.

These are right up your alley buddy, let's get it together!   :D

milw156

  • Crew
  • *
  • Posts: 684
  • Gender: Male
  • Respect: +379
    • Modutrak
Re: An N-Possible journal
« Reply #505 on: October 27, 2026, 02:21:18 PM »
0
You're not wrong... Anything else is just a Band-Aid on a sucking chest wound.

I saw someone who took the spring out of MTL couplers and replaced it with a length of a cut up rubberband of similar enuf diameter that eliminated the slinky in both the 1015s, &1025s, as well as truck mount couplers. I'm guessing length was about the same as the spring, just not so sure the rubber would last long without drying up or "melting".

peteski

  • Crew
  • *
  • Posts: 35440
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
Re: An N-Possible journal
« Reply #506 on: October 27, 2026, 09:16:39 PM »
0
I saw someone who took the spring out of MTL couplers and replaced it with a length of a cut up rubberband of similar enuf diameter that eliminated the slinky in both the 1015s, &1025s, as well as truck mount couplers. I'm guessing length was about the same as the spring, just not so sure the rubber would last long without drying up or "melting".

Yes, I heard that too, and yes, rubber (from elastics) will dry up or melt.
. . . 42 . . .

lock4244

  • Crew
  • *
  • Posts: 4603
  • Respect: +894
    • My train pics
Re: An N-Possible journal
« Reply #507 on: October 27, 2026, 10:09:17 PM »
0
I'd recommend mimicking the axle point wiper design for interior lighting on the first run of Prairie Shadows (by Rapido) CN PSC van's... excellent slinky fighters. This high friction design creates a fair amount of drag, and in my experience do make a noticeable difference. And they don't seem to wear in with use, so no fear of diminished results over time.

Dave V

  • Crew
  • *
  • Posts: 12424
  • Gender: Male
  • Foothills Farm Studios -- Dave's Model Railroading
  • Respect: +12073
Re: An N-Possible journal
« Reply #508 on: November 04, 2026, 04:25:19 PM »
+1
Turns out I had a pack of those axle springs after all. Installed them on three cabin cars. Worked like a charm.

I have several more cabin cars to go, but most of my springs sproinged into the aether as they are oft wont to do. Will need another pack at some point.

Thanks for the tip! This'll hold me over until I get around to a better coupling system.
« Last Edit: November 04, 2026, 06:32:32 PM by Dave V »

jpwisc

  • Crew
  • *
  • Posts: 1329
  • Gender: Male
  • Respect: +4014
    • Skally Line Blog
Re: An N-Possible journal
« Reply #509 on: November 09, 2026, 07:56:22 PM »
+1
ScaleTrains F68CH/F68DH flatcar. Medium shank URS.  If it wasn’t for the airhose and cut lever, this install would be a breeze! Good looking details getting in the way
[ Guests cannot view attachments ]
[ Guests cannot view attachments ]
[ Guests cannot view attachments ]
Karl
CEO of the WC White Pine Sub, an Upper Peninsula Branch Line.