Author Topic: A Tale of Two... Business Cars  (Read 8388 times)

0 Members and 1 Guest are viewing this topic.

Santa Fe Guy

  • Crew
  • *
  • Posts: 1096
  • Respect: +359
Re: A Tale of Two... Business Cars
« Reply #15 on: June 27, 2019, 07:39:26 PM »
0
Outstanding work, very impressive.
Rod.
Santafesd40.blogspot.com

craigolio1

  • Crew
  • *
  • Posts: 2739
  • Respect: +2388
Re: A Tale of Two... Business Cars
« Reply #16 on: June 27, 2019, 08:19:43 PM »
0
Thanks everyone. It’s very encouraging.

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #17 on: June 28, 2019, 08:32:50 AM »
0
Thanks everyone. It’s very encouraging.

Hey, don't feel too encouraged just yet... I'm still trying to catch up on my build! :trollface:

Agree 100% with the sentiment though, thanks everyone.

I guess your engineering degree is good for something after-all!

Really I just use my iron ring to cause shorts on the club layout and test circuit breaker protection...  :facepalm:
« Last Edit: June 28, 2019, 11:02:38 AM by CNR5529 »
Because why not...

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #18 on: June 28, 2019, 09:16:45 AM »
+4
...and I am catching up... slowly...

Last night Burrard got trucks and couplers. I still need to adjust the height a bit, which will happen shortly once the new floor goes in and the car is a bit more rigid.

[ Guests cannot view attachments ]

Next up was cutting out the original floor and cast in seats from the "Con-Core" coach, to make room for the new floor and steel plate weight.

[ Guests cannot view attachments ]

Unfortunately, in my haste I punched a hole through the side of the car while cutting out the floor. D'OH! Oh well, a bit of styrene cement patched that up pretty quickly.

[ Guests cannot view attachments ]

Finally I built up the vaulted porch ceiling, where the porch lights will eventually be installed. On 93, Craig installed a thick piece of styrene which is much more rigid, however looses the vaulted effect. That said, 93 appears to have always had curtains around the observation area, so it wont show either way. Burrard on the other hand didn't have curtains, so the vaulted ceiling effect will be a bit more noticeable. Once everything is cured properly, the corners will get rounded off a bit to match the roof.

[ Guests cannot view attachments ]
« Last Edit: June 28, 2019, 09:37:14 AM by CNR5529 »
Because why not...

craigolio1

  • Crew
  • *
  • Posts: 2739
  • Respect: +2388
Re: A Tale of Two... Business Cars
« Reply #19 on: June 28, 2019, 12:57:19 PM »
0
Nice. That vaulted ceiling looks great.

We need scale size couplers.

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #20 on: June 28, 2019, 01:07:28 PM »
+1
MT scale couplers would look great, but... I have seen a number of pictures of Burrard and Bedford mid-train while in active service. For that reason I think I'll have to keep the magnematic on the back... even if it just doesn't look right.  :|

« Last Edit: June 28, 2019, 01:25:03 PM by CNR5529 »
Because why not...

craigolio1

  • Crew
  • *
  • Posts: 2739
  • Respect: +2388
Re: A Tale of Two... Business Cars
« Reply #21 on: June 28, 2019, 01:24:57 PM »
0
MT scale couplers would look great, but... I have seen a number of pictures of Burrard mid-train while in active service. For that reason I think I'll have to keep the magnematic on the back.  :|

MT 905 Z scale.  Best compromise for sure.

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #22 on: July 02, 2019, 03:33:54 PM »
+1
I had to fix another "oops" over the weekend...

The drawing I had on hand for Burrard did not include a view of the end wall at the observation platform, so when cutting the sides, I chose to use the same end wall as that for car 93. After reviewing photos of the porch railings though, I noticed that 93 has taller windows than Burrard. Furthermore, the end door on 93 is framed by center posts (which we planned to install), while the end door on Burrard is recessed and the center posts are hidden by the end wall. Once I saw the difference, I couldn't un-see it, so it had to be replaced. :RUEffinKiddingMe:

Cue a sharp exacto blade.

[ Guests cannot view attachments ]

The end windows on Burrard look to be the same height as the side windows, so I resized them in the cad file. To simulate the recessed door, I decided to laminate two layers of styrene. The outer one has the two windows and door opening, while the inner one has the door window opening (which was also modified, based on pictures I could find). Here are the two end walls side by side.

[ Guests cannot view attachments ]

Once the new wall was sorted out, I proceeded to install a z scale coupler at the observation end, and set the final ride height.

[ Guests cannot view attachments ]

[ Guests cannot view attachments ]

[ Guests cannot view attachments ]

Finally, I installed a spare set of steps from Athabasca scale models. This one is very close to the correct shape for Burrard.

[ Guests cannot view attachments ]

Sorry for the crappy cellphone shots...

Oh, I also installed the new floor, but forgot to take a photo. It looks quite similar to what Craig did on 93.
Because why not...

craigolio1

  • Crew
  • *
  • Posts: 2739
  • Respect: +2388
Re: A Tale of Two... Business Cars
« Reply #23 on: July 02, 2019, 08:31:57 PM »
0
Yesssss!  Looks really good.

craigolio1

  • Crew
  • *
  • Posts: 2739
  • Respect: +2388
Re: A Tale of Two... Business Cars
« Reply #24 on: July 05, 2019, 08:26:48 PM »
+5
I got to work in a bit of lighting today.

I made table lamp shades by chucking 3/32” styrene in a drill and filing it until the tube wall was very thin. I measured and the diameter is now the equivalent of 10.5” in N scale. Here it is still in the drill and with an 0402 LED inside to check fit. I cut them off so they would be about 10” tall.



I had to solder leads on the LEDs axially as the are too wide to go in side ways.

Once I had two done I put LEDs inside and experimented with resistors. On a 9v battery with two LEDs in parallel, 30k of resistance produces a nice glow that it visible with the room lights on, and creates a warm pleasing glow with the lights off. Unfortunately my phone and I can’t take pictures of lights worth a damn. They are not nearly as bright in real life.





And with Peteski’s giant dime....




For the bases I’ll drill a hole in the middle of some styrene rod, glue it to the table, and then thread the lights in during final assembly.


Wall sconces will be made in a similar manor I think, but cut in half for wall mounting.

Craig
« Last Edit: July 05, 2019, 08:56:52 PM by craigolio1 »

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #25 on: July 05, 2019, 08:42:50 PM »
0
Man that is cool!!!
Because why not...

peteski

  • Crew
  • *
  • Posts: 35429
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6694
    • Coming (not so) soon...
Re: A Tale of Two... Business Cars
« Reply #26 on: July 05, 2019, 09:30:55 PM »
+2
Most excellent!


If they are too bright. you can always use higher value resistors to  dim them.

Back in the early '90s, long before 0402 (or any other) SMD LEDs were available, I have installed table lamps in a Con-Cor observation car.  I turned the shades on my Sherline lathe from translucent white acrylic and the light to each lamp was delivered via a plastic fiber optic, painted gold to look like a lamp's stem.  All the fiber optics were routed between the interior floor and the underframe to the kitchen area. There, a single 1.5V bulb supplied the light. It was powered by a constant-lighting circuit using a NiCad battery to keep the lamps illuminated when there was no track voltage (we ran trains on DC back them).

. . . 42 . . .

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #27 on: July 08, 2019, 09:25:41 AM »
+3
Nicely done Pete!

Time for Burrard to get an interior. Much like how Craig did the interior for 93, I started by making a template of the interior cross setction:

[ Guests cannot view attachments ]

Instead of using it to trace out and hand cut all the other partitions though, I measured it out and drew it up in cad. This made cutting a bunch of identical interior partitions on the silhouette a (score and) snap.

[ Guests cannot view attachments ]

Assembly went fairly quick, and pretty soon it was looking like a 7 compartment open observation lounge car!

[ Guests cannot view attachments ]

[ Guests cannot view attachments ]

I then harvested some bits from a Kato business car, and began populating the observation lounge and porter's room.

[ Guests cannot view attachments ]

[ Guests cannot view attachments ]

I still need two smaller tables for the two pairs of angled chairs, as well as a buffet hutch against the kitchen wall partition. Then I will make up some fold out beds and washroom partitions for the compartments.

As an aside, I recently came across these two photos of the interior of the observation end in Burrard, on the new Canada Science and Technology Museum digital archive website. Looks like the chairs and tables were moved around as needed (compared to the original floor plan). There are no table lamps or wall sconces either, so I guess I wont need to build any of those... lots of ceiling fixtures though! The wall paneling is also quite plain, likely beige or a pastel tone, with only a bit of pop coming from the curtains.



« Last Edit: July 08, 2019, 09:46:36 AM by CNR5529 »
Because why not...

craigolio1

  • Crew
  • *
  • Posts: 2739
  • Respect: +2388
Re: A Tale of Two... Business Cars
« Reply #28 on: July 08, 2019, 04:50:14 PM »
+1
You need to model THIS guy. He’s got swagger



Like a boss.

Craig.

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #29 on: July 08, 2019, 05:54:47 PM »
0
4-5 business types smoking pipes and drinking scotch? Done!
Because why not...