Author Topic: A Tale of Two... Business Cars  (Read 8388 times)

0 Members and 1 Guest are viewing this topic.

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
A Tale of Two... Business Cars
« on: June 26, 2019, 11:02:42 AM »
+2
It was the best of times, it was the worst of times, it was the age of wonderous RTR N scale announcements, it was the age of way too many projects at the work bench… speaking of which, time to show another project that’s in the pile!

Late last year, while discussing the multitude of passenger trains we were both building, @craigolio1 and I got on the subject of business cars. Funny thing is we are modeling practically the same trains, yet our rolling stock looks completely different because he models the late 80s and early 90s, while my efforts represent the mid 50s. Ok, back to the business cars, I think the conversation went something like this:

Craig: I want a business car in VIA colours for my Super Continental.

Me: Which one? I want a business car in CNR colours for my Super Continental, Burrard to be precise.

Craig: The one with the little side door, I saw it in Vancouver as a kid.

Me: Right…

So after a bit of digging around, we determined two things. One, Burrard is not actually a business car but rather one of two 7 compartment lounge open observation cars, built new to be used in revenue passenger service (the second car being Bedford). Two, there was a multitude of ex CNR business cars which were all similar and that were repainted in VIA colours, and many had the little side door. Car 93 though was typically spotted out west, so we figured it must have been the car he remembered. It, like many of the other business cars of that era, was rebuilt from a lightweight coach.

Here are the two cars in question. Both survive to this day, 93 having been rechristened “Tioga Pass” and Burrard running around as… Burrard (and still in CNR colours!).

93/Tioga Pass:





Burrard:





Both cars are of a lightweight design, which means I would be able to cut custom sides out of styrene with my silhouette cutter fairly quickly, and we could then laminate the sides onto a striped down donor car. We found some cheap Con Cor cars at a local show, which Craig volunteered to chop up and prep, and I found the drawings of both cars in one of my CNR reference books. Basically, we decided to make "Athabasca kits" for some of the few cars that were never produced. Time to get cutting!
« Last Edit: June 26, 2019, 11:50:41 AM by CNR5529 »
Because why not...

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #1 on: June 26, 2019, 11:10:19 AM »
+2
Here is a comparison drawing of both cars.

[ Guests cannot view attachments ]

These were traced out in cad, cleaned up, and imported into the Silhouette software.

[ Guests cannot view attachments ]

Finally, I was able to score and snap styrene to make the custom sides.

[ Guests cannot view attachments ]

[ Guests cannot view attachments ]

[ Guests cannot view attachments ]

By scoring little Xs in the windows I was able to quickly punch out the unwanted styrene. "Craig, don't accidentally punch out your little side door"  :trollface:

[ Guests cannot view attachments ]

All in all the sides came out quite nicely. Now we just have to assemble and go to town detail wise. Of course neither one of us will be outdone by the other, so the level of detail we are both planning (as Craig has already shown in some weekend updates) should be pretty cool. Did someone say functional table lamps?
« Last Edit: June 26, 2019, 11:20:05 AM by CNR5529 »
Because why not...

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #2 on: June 26, 2019, 11:16:03 AM »
+4
Last night I FINALLY got to assembling my car... So I am quite pleased to say, Burrard is starting to look like an actual piece of rolling stock!

[ Guests cannot view attachments ]

[ Guests cannot view attachments ]

The trucks are not yet fastened to the bolsters or even adjusted height wise for that mater, so that along with coupler installation will likely be my next task. After that, I believe I have a bit of catching up to do with the interior...
« Last Edit: June 26, 2019, 11:21:45 AM by CNR5529 »
Because why not...

ryan_wilkerson

  • Crew
  • *
  • Posts: 1100
  • Respect: +209
    • ShastaRails.com
Re: A Tale of Two... Business Cars
« Reply #3 on: June 26, 2019, 12:24:59 PM »
0
What a cool story and build thread. Both of those cars are familiar to me as the Burrard has been stored about 30 miles away from my house (and I've seen it on a few trains over the last decade).
My sons and I were able to ride Tioga Pass after the car owner Norm recognized us from a tour during the Dunsmuir (CA) Railroad Days. He saw us back in the coach section and invited us to ride on the platform with him! Was a great ride through the Feather River Canyon that weekend!
I'd love to replicate the Tioga Pass someday to tack on to the rear of the Coast Starlight.

u18b

  • Crew
  • *
  • Posts: 4056
  • Respect: +2388
    • My website
Re: A Tale of Two... Business Cars
« Reply #4 on: June 26, 2019, 12:46:36 PM »
0
Looks great!

On a side note.... I found the CN paint scheme interesting.  The yellow "separation stripes" don't separate anything.   The black continues a bit.
Ron Bearden
CSX N scale Archivist
http://u18b.com

"All get what they want-- not all like what they get."  Aslan the Lion in the Chronicles of Narnia by C.S.Lewis.

CNR5529

  • Crew
  • *
  • Posts: 654
  • Respect: +691
    • My Shapeways Store
Re: A Tale of Two... Business Cars
« Reply #5 on: June 26, 2019, 01:00:01 PM »
+1
The yellow "separation stripes" don't separate anything.   The black continues a bit.

Indeed! There is a thin black pinstripe between the yellow and green, that is accurate to the original scheme. Also, the three yellow stripes are all supposed to be different thicknesses. All this makes painting these cars a bit of a chore. Craig will have the slightly easier paint job to be sure...

What a cool story and build thread. Both of those cars are familiar to me as the Burrard has been stored about 30 miles away from my house (and I've seen it on a few trains over the last decade).
My sons and I were able to ride Tioga Pass after the car owner Norm recognized us from a tour during the Dunsmuir (CA) Railroad Days. He saw us back in the coach section and invited us to ride on the platform with him! Was a great ride through the Feather River Canyon that weekend!

That is so cool!! I certainly wouldn't say no to a ride in either car.
« Last Edit: June 26, 2019, 01:26:00 PM by CNR5529 »
Because why not...

craigolio1

  • Crew
  • *
  • Posts: 2739
  • Respect: +2388
Re: A Tale of Two... Business Cars
« Reply #6 on: June 26, 2019, 01:27:08 PM »
+1
Don’t cut out the little door he says. Hahah. Great story Fredrick.

Oh, and yeah I did cut out the door but you probably all guessed that.

I’m hung up in the rear platform railing right now but I need to paint it before I tackle that anyway. So next up for me is to finish the interior (did someone say working table lamps AND wall sconces?) and paint.

I’ll post pics soon.

Craig.

peteski

  • Crew
  • *
  • Posts: 35429
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6694
    • Coming (not so) soon...
Re: A Tale of Two... Business Cars
« Reply #7 on: June 26, 2019, 02:16:01 PM »
0
You're off to a great start guys!
...should be an interesting thread to follow.
. . . 42 . . .

craigolio1

  • Crew
  • *
  • Posts: 2739
  • Respect: +2388
Re: A Tale of Two... Business Cars
« Reply #8 on: June 27, 2019, 03:56:50 PM »
+5
Time to jump in with some progress photos.

I started by taking two Concor cars that we scored on the cheap and at a show, (Con-CORE?, sorry...  I couldn't resist), and making a wood block to fit snugly inside, allowing me to turn this:




Into this:



I laid a full sheet of 220 grit paper on my table and just kept doing 10 circles in each alternating direction until enough was removed that the styrene sides nestled in under the roof.

Following that I turned a coach roof into a business car roof by cutting 45 degree wedges out of a donor roof and transplanting them into a similar size wedge cut in to the end of the coach roof.  I started small and slowly opened the wedge up more and more until it was almost a perfect fit that just a little filler fixed up nicely.... well on Fredrick's anyway.  Something went awry in my mitre box on my first attempt, as you can see on the left roof, and I needed to cut another filler wedge, but all's well that ENDS well.





The sides were laminated on and I used I piece of styrene to fill in the back porch roof.  I should have used a thinner piece to create a recess under the ceiling.  Fredrick can do that on his.





Starting to look like a business car.



Next I sorted out a floor, weight, trucks and couplers.

I wanted to be able to run wires under the floor and have them be concealed so the floor is on a thin spacer.  This allowed me to use a hardware store connector place as a weight. (They are  little on the thick side).  This isn't a great photo but it shows the weight, and also the 3/32 styrene tube I used to mount the Rapido trucks.  Note this end has shoulders filed for and aft on the tube which eliminates side to side rocking.  Fredrick I guess your engineering degree is good for something after-all!



I mounted MT 1015s with an 040" styrene shim, and one MT shim from the 1015 package.  Height looks good to me.



Next I moved into the interior.  Based on the drawing Fredrick gave me, I was able to scale the locations of walls and furniture.  Interior partition walls are .030" styrene, and seats were cannibalized from two Kato business car interiors. I made the two side tables out of styrene. The only rooms I'm detailing are the dining room, rear sitting area, and adjoining hallway.  They will have open windows.  The other rooms’ windows will be covered with blinds.







For the interior side walls, Fredrick is going to cut matching interior wall panels out of.... undetermined.  The idea is to be able to hid wall sconce wiring behind these panels, so it can look like this....



Prior to their installation, the interior walls be be painted black and then silver to prevent light bleeding through the sides.  I'll then run the wires for the LEDs, install the windows, and cover them up with the wall panels.

But before that happens I needed to tackle the rear porch lighting and markers.  There is a lot of lighting in a very small space back there.  The rear proch lights, pictured below, don't need to be really bright, just present.



To keep the wiring to a minimum I opted to light the center light with an 0603 LED and then the two on each side with fibre optics.  First I applied some metal foil, then I installed the LED and fibers (i bent the fibers with a soldering iron and polished both ends).  I covered the whole mess with more foil tape.



The effect is really nice, although the center light is a little hot, but it's not really noticeable unless you get under it which won't happen too often during opps. If I were to do it again I think I would try it with three LEDs. I didn’t wind up saving the space I thought I would with the fibres. There would still be room above for the marker lights and I would have more control over the intensity.





With this completed I had to figure how to now fit two marker lights in there.  I settled on brass tubing, which I would fit with fiber optics, and run back through the roof to a loaction at the other end of the car where the electronics will go.  The fibre will bend at a 90 degree angle and fit in a tube holding a red LED, mounted on the floor.  This will ensure no wires have to run between the roof and the car for when I want to pop the roof to show the interior.

I soldered two brass tubes together and then filed them to the right shape. 




Then I CAREFULLY drilled, drilled larger, then larger, holes and widened them to fit the brass tubes.  For anyone that has not cut into these Concor roofs before the plastic is brittle and splinters. Because I was drilling into the sloped end the actual thickness of the material was quite thick, and being so close to the edges I was concerned the corners of the roof would explode. So I went very slowly with several sizes of drill bit starting with a #80. Here is the result.



Next I detailed to roof. I scribed panel lines and added a few details.  It will get Archer rivet decals as well but prior to that I figured I should see just how much damage I've done so I shot a primer coat.  It needs some love but all and all I'm really pleased with the progress so far.



Once I clean up the model a bit the next step for me will be interior paint.

Craig

PS I just realized I forgot the centre rear light, so I guess thats next...   and I fixed the litle side door




« Last Edit: June 27, 2019, 06:19:43 PM by craigolio1 »

Lemosteam

  • Crew
  • *
  • Posts: 6463
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5026
Re: A Tale of Two... Business Cars
« Reply #9 on: June 27, 2019, 04:05:05 PM »
0
Outstanding!
John "Lemosteam" LeMerise

CHUCKGEO

  • Crew
  • *
  • Posts: 58
  • Respect: +126
Re: A Tale of Two... Business Cars
« Reply #10 on: June 27, 2019, 04:30:14 PM »
0
Nice job. Great detail.

peteski

  • Crew
  • *
  • Posts: 35429
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6694
    • Coming (not so) soon...
Re: A Tale of Two... Business Cars
« Reply #11 on: June 27, 2019, 05:47:10 PM »
0
Nice job. Great detail.

Looking good!
What material was used for the weight?  In the photo it looks like aluminum (which wouldn't have much weight at all).  Brass or steel (or of course sheet lead) would be a heavier option.
. . . 42 . . .

nickelplate759

  • Crew
  • *
  • Posts: 3885
  • Respect: +1662
Re: A Tale of Two... Business Cars
« Reply #12 on: June 27, 2019, 06:09:10 PM »
0
that looks like a standard hardware-store splice plate.  They're normally plated steel.
George
NKPH&TS #3628

I'm sorry Dave, I'm afraid I can't do that.

peteski

  • Crew
  • *
  • Posts: 35429
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6694
    • Coming (not so) soon...
Re: A Tale of Two... Business Cars
« Reply #13 on: June 27, 2019, 06:18:17 PM »
0
that looks like a standard hardware-store splice plate.  They're normally plated steel.

In the photo it looks like that whitish-silver aluminum color - that is why I asked. Steel usually looks darker. It's probably  just the lighting.
. . . 42 . . .

craigolio1

  • Crew
  • *
  • Posts: 2739
  • Respect: +2388
Re: A Tale of Two... Business Cars
« Reply #14 on: June 27, 2019, 06:21:02 PM »
0
In the photo it looks like that whitish-silver aluminum color - that is why I asked. Steel usually looks darker. It's probably  just the lighting.

Steel. It’s actually a little too heavy I think. I need to weight and probably trim the weight.