Author Topic: N Scale Hi Rail - Retro Hollow Core Door Layout  (Read 262469 times)

0 Members and 1 Guest are viewing this topic.

wm3798

  • Crew
  • *
  • Posts: 16589
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7524
    • Western Maryland Railway Western Lines
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1170 on: November 02, 2020, 08:22:05 PM »
+1
@Point353 , I dig your jive.

I've been struggling with the mill race since I posted the picture.  The only issue I would have with bending the track to angle the building more to the rear is that it would make coupling the cars in the siding would become more difficult since it would be on a tight curve.

But the idea bears experimentation...  Plus, it would make the spinning water wheel more visible to the primary viewing angle of the scene....  Thanks for that feedback.
Lee
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

Point353

  • Crew
  • *
  • Posts: 3770
  • Respect: +928
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1171 on: November 02, 2020, 08:37:53 PM »
0
@Point353 , I dig your jive.

I've been struggling with the mill race since I posted the picture.  The only issue I would have with bending the track to angle the building more to the rear is that it would make coupling the cars in the siding would become more difficult since it would be on a tight curve.

But the idea bears experimentation...  Plus, it would make the spinning water wheel more visible to the primary viewing angle of the scene....  Thanks for that feedback.
Lee
I wasn't suggesting that the siding track needed to be moved at all.
But, maybe the available space is tighter than it appears in the photos.
To me, it looks at though the sawmill would still fit if you cut off the base on the side with the large door opening and then rotated the sawmill 90° so that the door opening faces the siding track (and the waterwheel is adjacent to the ravine).

wm3798

  • Crew
  • *
  • Posts: 16589
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7524
    • Western Maryland Railway Western Lines
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1172 on: November 02, 2020, 09:13:18 PM »
+1
I see what you're saying...  The large door on the left has a narrow gauge track cast into the floor...  I reckon for feeding logs into the mill.  The large door at the other end is more of a warehouse door.  That might make more sense.  Then the loading dock that I was locating next to the siding could be used for trucks to be loaded...  Hmmm...
Lee
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

DKS

  • The Pitt
  • Crew
  • *
  • Posts: 13424
  • Respect: +7027
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1173 on: November 03, 2020, 04:59:57 AM »
0
OK, I'll play along. How about pulling the Peco shorty and the curved track to its left, then install the Trix turnout as far left as you can. Then, off the straight leg, run a siding roughly parallel to the mainline and curve it tightly, such that the mill can be installed roughly parallel to the crossover. The other siding can swing up parallel to the ravine.

Here's a few thousand words, very crudely:



The mill siding curve would be insanely tight, but hey, this is retro after all.
« Last Edit: November 03, 2020, 05:07:25 AM by DKS »

wm3798

  • Crew
  • *
  • Posts: 16589
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7524
    • Western Maryland Railway Western Lines
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1174 on: November 03, 2020, 09:58:00 AM »
+1
On @Point353 's suggestion, I rotated the sawmill 90 degrees, and left the track plan more or less as is.  This accomplishes several things. 
1.  The mill race now parallels the stream bed, and gives me the opportunity to make a mill pond around the corner of the skyboard that masks the staging area back there.  The turning mill wheel will also be more evident.
2.  The "track" that would feed logs into the mill now terminates at the siding, so a small crane can be added to unload a flat car.
3.  Real estate is now freed up to create a bit of a yard where finished product can be stacked.  I can add a boxcar loading ramp at the end of the siding wide enough for a forklift to navigate.



I can light the whole thing up with LEDs as you can see I have a wire terminal right there in the neighborhood.

Thanks for all the suggestions!  Not bad for about 12 inches square!
Lee
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

CRL

  • Crew
  • *
  • Posts: 2345
  • Needs More Dirt.
  • Respect: +643
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1175 on: November 03, 2020, 05:57:48 PM »
0
OK, I'll play along. How about pulling the Peco shorty and the curved track to its left, then install the Trix turnout as far left as you can. Then, off the straight leg, run a siding roughly parallel to the mainline and curve it tightly, such that the mill can be installed roughly parallel to the crossover. The other siding can swing up parallel to the ravine.

Here's a few thousand words, very crudely:



The mill siding curve would be insanely tight, but hey, this is retro after all.

Insanely tight can be a very good thing in industrial trackage, especially if you restrict the locos from the spur and use reacher cars to pull & spot cars at the industry. Makes for fun operations.

To “enforce” the no locos rule, insulate the siding and don’t add drops so it’s electrically dead.
« Last Edit: November 03, 2020, 06:00:26 PM by CRL »

wm3798

  • Crew
  • *
  • Posts: 16589
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7524
    • Western Maryland Railway Western Lines
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1176 on: November 03, 2020, 07:39:05 PM »
0
I'll hold that idea for the next micro layout.  I've got this one pretty well sorted now.
I do have a couple of Plymouths that could be pressed into service on the "insanely" tight turn, but there's just not much room to work with for extra spacer cars etc. 
I played with switching the new set up today, and it works out fine.  3-4 cars from this side, and 4 55T hoppers from the truck dump at the other side works out nicely, and doesn't tax the switcher beyond its capabilities.
I also have to keep in mind the scenery elements, so no more shifting at this point.
Lee
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

OldEastRR

  • Crew
  • *
  • Posts: 3801
  • Gender: Male
  • Respect: +518
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1177 on: November 05, 2020, 01:32:08 PM »
0
And for true fidelity to how N scale layouts were done back then, no real access for road vehicles. I especially liked how people would stick a factory in the midst of a bunch of track, then put a 40'semi- loading at it with absolutely no way in hell it could have got there except by being air-lifted in.

But you're being true to the era.

davefoxx

  • Crew
  • *
  • Posts: 12400
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8795
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1178 on: November 05, 2020, 02:02:01 PM »
+1
And for true fidelity to how N scale layouts were done back then, no real access for road vehicles. I especially liked how people would stick a factory in the midst of a bunch of track, then put a 40'semi- loading at it with absolutely no way in hell it could have got there except by being air-lifted in.

But you're being true to the era.

Some modelers still do that.  A pet peeve of mine.

DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

CRL

  • Crew
  • *
  • Posts: 2345
  • Needs More Dirt.
  • Respect: +643
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1179 on: November 05, 2020, 02:04:35 PM »
0
No parking lot for employees... unless steam era, then within walking distance of non-existent town.

Plus no toxic waste flowing into the nearby stream.
« Last Edit: November 05, 2020, 02:06:07 PM by CRL »

wm3798

  • Crew
  • *
  • Posts: 16589
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7524
    • Western Maryland Railway Western Lines
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1180 on: November 07, 2020, 05:49:42 PM »
0
I need a Mehano GP40 cab roof.


And some end handrails.

Don't ask why.

Lee
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

wm3798

  • Crew
  • *
  • Posts: 16589
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7524
    • Western Maryland Railway Western Lines
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1181 on: November 09, 2020, 04:21:02 PM »
0
Making hay while the sun shines...


My Atlas "Collectible" edition C Liners bask in the sunlight on my roundhouse module.

Lee
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

peteski

  • Crew
  • *
  • Posts: 35427
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6693
    • Coming (not so) soon...
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1182 on: November 09, 2020, 05:19:47 PM »
0
Making hay while the sun shines...


My Atlas "Collectible" edition C Liners bask in the sunlight on my roundhouse module.

Lee

Wow!  Those are really cool!  Do they have a truck-mounted pancake, or a vertically-mounted conventional motor with a crappy vinyl magnet?  Do they actually run?
. . . 42 . . .

wm3798

  • Crew
  • *
  • Posts: 16589
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7524
    • Western Maryland Railway Western Lines
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1183 on: November 09, 2020, 09:48:58 PM »
0
It's a powered A-dummy A set, with the vertical can motor powering the front truck.
And yes, it runs surprisingly well!
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

CRL

  • Crew
  • *
  • Posts: 2345
  • Needs More Dirt.
  • Respect: +643
Re: N Scale Hi Rail - Retro Hollow Core Door Layout
« Reply #1184 on: November 09, 2020, 10:55:07 PM »
0
You know, a dummy A unit as the lead unit is a good location for a video camera.