Author Topic: Bachmann Decoder Swap : 44 ton or 4-6-0  (Read 3804 times)

0 Members and 1 Guest are viewing this topic.

Mike the Modeler

  • Crew
  • *
  • Posts: 43
  • Respect: +105
Bachmann Decoder Swap : 44 ton or 4-6-0
« on: October 23, 2017, 01:56:46 AM »
0
Has anyone found any benefit to swapping out the decoder in an N scale Bachmann GE 44 Ton or their 4-6-0 locomotive?
I am looking to have improved motor control  capabilities.
Also wondering if it may quiet the buzz and vibration these things emit at low speeds.
The 4-6-0 rattles the doors in the 5 WOT baggage cars of the train it is pulling. 

JMaurer1

  • Crew
  • *
  • Posts: 1188
  • Gender: Male
  • Respect: +307
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #1 on: October 23, 2017, 12:51:32 PM »
0
While I haven't done it, the Bachmann decoders are not known to be cutting edge tech (or even dull edge tech). Swapping them out will most likely improve running characteristics. The decoders they come with are known for being... 'inexpensive', not necessarily good.
Sacramento Valley NRail and NTrak
We're always looking for new members

peteski

  • Crew
  • *
  • Posts: 35428
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6693
    • Coming (not so) soon...
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #2 on: October 23, 2017, 01:36:22 PM »
0
Yes, replacing the Bachmann decoder will make it work better (for the reasons stated earlier)
I have designed and etched about a dozen of retrofit boards for the 44-tonner which accommodate a typical small 6-pin decoder (like Digitrax DZ125 or similar). One of my many in-progress projects.  At some point I'll make it available for sale to the Railwire members who expressed interest.

Here is the original thread about this: https://www.therailwire.net/forum/index.php?topic=32605.0


I'll try to replace all the broken links to the Photobucket photos soon (uploading the photos here and updating my older posts is one of those in-progress projects).   :facepalm:
The photos are now fixed.
« Last Edit: October 23, 2017, 09:00:08 PM by peteski »
. . . 42 . . .

wm3798

  • Crew
  • *
  • Posts: 16589
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7524
    • Western Maryland Railway Western Lines
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #3 on: October 23, 2017, 04:33:01 PM »
0
The main thing that makes my head spin about Bachmann's chips is their complete inability to remember to keep the headlight on when even the tiniest stall occurs.

Pete, I'd be interested in a replacement board for the 44T, and I've got an S4 and a their SW whatever and an RS-3 as well.  They all pretty much stay on the shelf while an Atlas GP38 does all the work on the layout.
Lee
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

peteski

  • Crew
  • *
  • Posts: 35428
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6693
    • Coming (not so) soon...
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #4 on: October 23, 2017, 09:00:46 PM »
0
The main thing that makes my head spin about Bachmann's chips is their complete inability to remember to keep the headlight on when even the tiniest stall occurs.

Pete, I'd be interested in a replacement board for the 44T, and I've got an S4 and a their SW whatever and an RS-3 as well.  They all pretty much stay on the shelf while an Atlas GP38 does all the work on the layout.
Lee

Sure Lee, I'll let you know when the boards are ready.
. . . 42 . . .

Altoona

  • Crew
  • *
  • Posts: 171
  • Respect: +12
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #5 on: October 23, 2017, 10:33:09 PM »
0
I used a TCS mza4 and had to trim down the LED'S.

Judd Barton

ns737

  • Crew
  • *
  • Posts: 234
  • Respect: +38
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #6 on: October 23, 2017, 10:41:17 PM »
0
I have the Bachmann gp7 with decoder that my kids got me for my birthday 5yrs ago and it still runs great.

Mike the Modeler

  • Crew
  • *
  • Posts: 43
  • Respect: +105
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #7 on: October 24, 2017, 01:12:51 AM »
0
Yes, replacing the Bachmann decoder will make it work better (for the reasons stated earlier)
I have designed and etched about a dozen of retrofit boards for the 44-tonner which accommodate a typical small 6-pin decoder (like Digitrax DZ125 or similar). One of my many in-progress projects.  At some point I'll make it available for sale to the Railwire members who expressed interest.

Here is the original thread about this: https://www.therailwire.net/forum/index.php?topic=32605.0


I'll try to replace all the broken links to the Photobucket photos soon (uploading the photos here and updating my older posts is one of those in-progress projects).   :facepalm:
The photos are now fixed.

Thank you Mr Peterski
Very clever and tidy!
I would be happy to buy two boards or two assembled units ( sans the o.c.p.) if you get back to a making them.
Any word on if it clears up the buzzing sound?

peteski

  • Crew
  • *
  • Posts: 35428
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6693
    • Coming (not so) soon...
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #8 on: October 24, 2017, 02:09:11 AM »
0
Thank you Mr Peterski
Very clever and tidy!
I would be happy to buy two boards or two assembled units ( sans the o.c.p.) if you get back to a making them.
Any word on if it clears up the buzzing sound?

Thank you Mike.
The buzzing sound is due to Bachmann decoders using low frequency pulses for driving the motor. Most other brands of decoders use higher frequency pulses that do not create that buzz.  I will announce when the boards are ready.
. . . 42 . . .

Mike the Modeler

  • Crew
  • *
  • Posts: 43
  • Respect: +105
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #9 on: October 24, 2017, 03:00:34 AM »
0
Thank you Mike.
The buzzing sound is due to Bachmann decoders using low frequency pulses for driving the motor. Most other brands of decoders use higher frequency pulses that do not create that buzz.  I will announce when the boards are ready.

On a related note. You did a nice piece on the Arnold SW1. I recall there was a related thread about the best decoder choice for that loco. It mentioned ZIMO decoders because they are built to work with coreless motors. It is my current understanding that the Bachmann 44 tonner and other Bachmann products use a coreless motor. Do you have insight into whether this ZIMO circuitry adds a benefit over say the DZ125 when paired with a coreless motor?

Jim Starbuck

  • Crew
  • *
  • Posts: 1066
  • Respect: +3182
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #10 on: October 24, 2017, 08:22:41 AM »
+1
I replaced the stock decoder in my 44t with a hardwired TCS Z2.
I also removed the light block from the cab because it wasn't necessary as the lights are micro LEDs mounted in the shell and fed with magnet wire.
The engine runs nicely and has independent control for the lights with directional dimming and pushbutton dimming of the active light.
Modutrak Iowa Division
Modutrak.com
Better modeling through peer pressure

Lemosteam

  • Crew
  • *
  • Posts: 6463
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5026
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #11 on: October 24, 2017, 08:36:14 AM »
0
I replaced the stock decoder in my 44t with a hardwired TCS Z2.
I also removed the light block from the cab because it wasn't necessary as the lights are micro LEDs mounted in the shell and fed with magnet wire.
The engine runs nicely and has independent control for the lights with directional dimming and pushbutton dimming of the active light.

Did you photograph your process at all?  Would love to see that install.
John "Lemosteam" LeMerise

peteski

  • Crew
  • *
  • Posts: 35428
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6693
    • Coming (not so) soon...
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #12 on: October 24, 2017, 09:48:27 AM »
0
On a related note. You did a nice piece on the Arnold SW1. I recall there was a related thread about the best decoder choice for that loco. It mentioned ZIMO decoders because they are built to work with coreless motors. It is my current understanding that the Bachmann 44 tonner and other Bachmann products use a coreless motor. Do you have insight into whether this ZIMO circuitry adds a benefit over say the DZ125 when paired with a coreless motor?

The 44-tonner has a conventional motor (not a coreless), but installing a quality decoder like ZIMO will result in a very good motor control.  And it also handles coreless motors very well.
. . . 42 . . .

Jim Starbuck

  • Crew
  • *
  • Posts: 1066
  • Respect: +3182
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #13 on: October 24, 2017, 10:07:49 AM »
0
Did you photograph your process at all?  Would love to see that install.
I don't have any pictures with me and I won't be home until tomorrow night.
As I remember though it was very straightforward with no frame modification.
Modutrak Iowa Division
Modutrak.com
Better modeling through peer pressure

peteski

  • Crew
  • *
  • Posts: 35428
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6693
    • Coming (not so) soon...
Re: Bachmann Decoder Swap : 44 ton or 4-6-0
« Reply #14 on: October 24, 2017, 11:07:06 AM »
0
I don't have any pictures with me and I won't be home until tomorrow night.
As I remember though it was very straightforward with no frame modification.

So you  just removed the original and replaced it with the wired-in Z2?  Then attached "umbilical wires" for the shell-mounted LEDs? My anal nature would not allow me to do that (not neat enough).  I hate having the shell tethered by wires. I had to do it my way (but  there is nothing inherently wrong with a wired-in install).  :)
. . . 42 . . .