Author Topic: Looking for large industrial building window arrays  (Read 5234 times)

0 Members and 1 Guest are viewing this topic.

Lemosteam

  • Crew
  • *
  • Posts: 6467
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5028
Re: Looking for large industrial building window arrays
« Reply #15 on: December 29, 2016, 07:07:46 AM »
0
Laser printing does the trick.  I've used it for several projects, all with great success.

I have laser printed on clear sticky back film (drawing notes on a Mylar drawings) and also on clear acetate presentation transparencies (remember the old overhead projectors?), this is relatively inexpensive and can be printed over and over.

Not sure how greyscale would work to achieve the various shades in your image though, but it looks like there is something behind the glass anyway. Mounted in a u channel, it should be fairly rigid to hold itself up, or you could mount it to clear styrene.
John "Lemosteam" LeMerise

OldEastRR

  • Crew
  • *
  • Posts: 3803
  • Gender: Male
  • Respect: +518
Re: Looking for large industrial building window arrays
« Reply #16 on: December 30, 2016, 12:51:03 AM »
0
I have laser printed on clear sticky back film (drawing notes on a Mylar drawings) and also on clear acetate presentation transparencies (remember the old overhead projectors?), this is relatively inexpensive and can be printed over and over.

Not sure how greyscale would work to achieve the various shades in your image though, but it looks like there is something behind the glass anyway. Mounted in a u channel, it should be fairly rigid to hold itself up, or you could mount it to clear styrene.

What kind of relief does the window muntins have above the plastic with this method? The plastic windows used for the rest of the plant are 3D and well-defined. I'm going to need these windows to have somewhat the same look.
Also, what size window panes would they be?

nkalanaga

  • Crew
  • *
  • Posts: 10610
  • Respect: +1776
Re: Looking for large industrial building window arrays
« Reply #17 on: December 30, 2016, 01:37:38 AM »
0
Very little relief, but the actual pane/frame relief is quite small on many such windows.  The main frames, exterior support pillars, etc can be added with styrene strips.

As for the size, since you'll be doing your own art, they can be any size you like.  For Excel, set the cell size to give the size you want, or if it won't go that small, set it to the desired proportions, print it on paper, and reduce it on a copier.  That's what I had to do to mine.

Mine were roundhouse windows, so not that large, and I glued them into the brick walls like any other window.  For yours, since there is a visible building framework behind them, support shouldn't be a problem. 
In Paint, or a similar program, you can draw whatever you like, save it as an image, and print it to the desired size.

With a true graphics program, you can probably do a lot more, but I have no experience with those.
N Kalanaga
Be well

peteski

  • Crew
  • *
  • Posts: 35434
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
Re: Looking for large industrial building window arrays
« Reply #18 on: December 30, 2016, 03:25:37 AM »
0
What kind of relief does the window muntins have above the plastic with this method?

Relief?  Whatever the thickness of the toner deposited on the substrate is. Take a sheet of paper with laser printed image or text on it - whatever ink thickness you see or don't see, that will be the relief of ink printed on the transparency too.  Well, it might be a little more pronounced since the toner will not be absorbed into the transparency, but we are still talking microns in thickness.
. . . 42 . . .

OldEastRR

  • Crew
  • *
  • Posts: 3803
  • Gender: Male
  • Respect: +518
Re: Looking for large industrial building window arrays
« Reply #19 on: December 30, 2016, 05:16:20 AM »
0
Having clear windows or just the muntins (Archer decals) is fine -- the windows w/ clear backing will be glued to a structure wall that will be painted to match the color patterns of the windows. The muntins/clear glass is glued to the backing, so the colors will look realistic but the outside of the "glass" would still be reflective. At least that's the theory. After all it's the inside of the real windows that are stained, not the outside.

Lemosteam

  • Crew
  • *
  • Posts: 6467
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5028
Re: Looking for large industrial building window arrays
« Reply #20 on: December 30, 2016, 09:19:53 AM »
0
The archer decals will not do that.  On the site it tells you that the clear substrate will be muddled due to the clear decal backing film.

I used to have steel frame windows in my house.  All of the structure/thickness was on the inside of the house for the glazing, not the outside.  the frames only stood proud of the glass by 1/8" in 1:1 on the outside of the house.  Yes tyou could make any rectangle sizes you wanted.  I have a full box of 8.5" x 11" clear transparency sheets that I can send you some.  How many square inches of area do you need to cover?

John "Lemosteam" LeMerise

jdcolombo

  • Crew
  • *
  • Posts: 2399
  • Respect: +1213
Re: Looking for large industrial building window arrays
« Reply #21 on: December 30, 2016, 10:04:45 AM »
0
The archer decals will not do that.  On the site it tells you that the clear substrate will be muddled due to the clear decal backing film.

I used to have steel frame windows in my house.  All of the structure/thickness was on the inside of the house for the glazing, not the outside.  the frames only stood proud of the glass by 1/8" in 1:1 on the outside of the house.  Yes tyou could make any rectangle sizes you wanted.  I have a full box of 8.5" x 11" clear transparency sheets that I can send you some.  How many square inches of area do you need to cover?

Hi John.

Since Old East is asking these questions on my behalf as part of the National Carbon project for my layout, I'll chime in here.  I have some transparency sheet, an HP laser printer, and Adobe Illustrator to work with.  I'm going to try to lay out something that looks like the photo this thread started with, and see how it works out.  It shouldn't be too hard to do that - I'll run some test prints on plain paper, and go from there.  I think we're going to try a bunch of different things to see what works best - my first thought was to have these windows either 3D printed or etched brass, but you all have suggested other techniques that may work just as well (and I realized that the 3D printing option probably wouldn't work given how fine the latticework would have to be).  The Micron Art windows, however, might have a place in this project (I've used their stuff in the past - my cornfield was made from Micron Art corn stalks long before we had the plastic corn sheets from Bluford).  Since we're only modeling one side of the building (the other side will be sitting next to the backdrop), it's not going to cost a fortune to do this no matter what technique we end up with.

And thanks to everyone for the suggestions so far - I didn't realize some of these sources for textures and scratch-building supplies were out there!

John C.

Dave Schneider

  • Crew
  • *
  • Posts: 2377
  • Respect: +51
Re: Looking for large industrial building window arrays
« Reply #22 on: December 30, 2016, 02:45:12 PM »
0
I have done windows in a couple of ways.

This one involves the use of vinyl tape over clear styrene and using my Silhouette cutter to cut the muntins and then remove the tape over the "window pane".





In this example I used masking tape over clear styrene, used the Silhouette to cut a mask, remove the part for the muntins and then sprayed the color. Finally the tape over the window pane is removed.







Finally, here is an example of laser printer on overhead transparency with a mottled paper background.





Best wishes, Dave
« Last Edit: December 30, 2016, 02:46:53 PM by Dave Schneider »
If you lend someone $20, and never see that person again, it was probably worth it.

jdcolombo

  • Crew
  • *
  • Posts: 2399
  • Respect: +1213
Re: Looking for large industrial building window arrays
« Reply #23 on: December 30, 2016, 03:01:34 PM »
0
OK - you got me.

What's a Silhouette cutter?

John C.

Dave Schneider

  • Crew
  • *
  • Posts: 2377
  • Respect: +51
Re: Looking for large industrial building window arrays
« Reply #24 on: December 30, 2016, 03:13:42 PM »
0
John,

It is a machine made for scrap book and craft people.
https://www.silhouetteamerica.com/shop/machines

A fair bit of discussion about these machines with pluses and minuses. It is not a silver bullet, but has many useful applications.
https://www.therailwire.net/forum/index.php?topic=23354.0

Hope this helps.
Best wishes, Dave
If you lend someone $20, and never see that person again, it was probably worth it.

peteski

  • Crew
  • *
  • Posts: 35434
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
Re: Looking for large industrial building window arrays
« Reply #25 on: December 30, 2016, 03:16:40 PM »
0
Silhouette is just one of many brands of computer controller craft cutters available. There is Cricut, CraftROBO and few others I don't recall right now.
. . . 42 . . .

Lemosteam

  • Crew
  • *
  • Posts: 6467
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5028
Re: Looking for large industrial building window arrays
« Reply #26 on: January 27, 2017, 01:12:28 PM »
0
@OldEastRR and @jdcolombo ,

So I finally got the chance to try printing window mullions on acetate for my Watch Box kit and here are the results (clear acetate is resting on a white sheet of paper...:



This is a test print from a .pdf file.  I will be using much thinner lines on the next pass.  What I find cool is the toner buildup thickness can be felt and seen.

This opens up multitudes of possibilities IMHO.
« Last Edit: January 27, 2017, 02:46:13 PM by Lemosteam »
John "Lemosteam" LeMerise

mighalpern

  • Crew
  • *
  • Posts: 278
  • Respect: +142
Re: Looking for large industrial building window arrays
« Reply #27 on: January 27, 2017, 02:34:41 PM »
0
cant see the picture

jdcolombo

  • Crew
  • *
  • Posts: 2399
  • Respect: +1213
Re: Looking for large industrial building window arrays
« Reply #28 on: January 27, 2017, 02:35:22 PM »
0
Hi John.

Your photo (?) isn't coming through for me on your post.

We decided to go with the laser printing on transparency, too.  I was waiting to post about this until the building is finished; Old East is working on finding the best solution for weathering the windows.  The laser prints look really good, however.

Any idea what the best way is to glue acetate (transparency film) to styrene?  The web seems to say Ethyl CA, but I'm open to suggestions . . .

John C.

Lemosteam

  • Crew
  • *
  • Posts: 6467
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5028
Re: Looking for large industrial building window arrays
« Reply #29 on: January 27, 2017, 02:46:29 PM »
0
Better?

[ Guests cannot view attachments ]
« Last Edit: January 27, 2017, 02:49:07 PM by Lemosteam »
John "Lemosteam" LeMerise