« previous next »
Pages: [1]   Go Down

Author Topic: Atlas NE-6 Caboose and Body-Mounted 2004 Couplers?  (Read 1443 times)

0 Members and 1 Guest are viewing this topic.

Kisatchie

  • Crew
  • *
  • Posts: 4180
  • Gender: Male
  • Respect: +63
Atlas NE-6 Caboose and Body-Mounted 2004 Couplers?
« on: November 15, 2013, 02:13:40 PM »
0
I got an Atlas NE-6 caboose today, but it didn't have couplers. I figured, "that's okay. I have a ton of Accumate couplers to put on it."

Ha ha, did Atlas surprise me. There is an odd, 2-diameter boss on the coupler lid that is too fat at the bottom for the Accumates I have. I guess Atlas makes a unique coupler for this caboose.

Anyhow, I went to Micro-Trains coupler conversion charts and found the NE-6 caboose. Here is what the chart said about using their 2004 body-mount couplers:

Stock
Remove Coupler box and cut
the mounting bosses from the 
under-side of porch of to
accept the body mount.  Trim
screw flush with the top of the
porch and touch up with paint.

Uhh... what about that screw? Does Micro-Trains give complete directions with the 2004 coupler pack?


Hmm... they better. Kiz
is all thumbs lately...

Logged
Two scientists create a teleportation ray, and they try it out on a cricket. They put the cricket on one of the two teleportation pads in the room, and they turn the ray on.
The cricket jumps across the room onto the other pad.
"It works! It works!"

Cory Rothlisberger

  • Crew
  • *
  • Posts: 306
  • Respect: +726
Re: Atlas NE-6 Caboose and Body-Mounted 2004 Couplers?
« Reply #1 on: November 15, 2013, 02:33:13 PM »
0
Uhh, we didn't use a special coupler on the NE-6. Did you try installing the Accumate? The coupler should only fit over that first boss on the cover. The second boss acts as a shim to maintain the coupler height. The box was big because at one time, you could pop the Rapido couplers in them.
Logged

Kisatchie

  • Crew
  • *
  • Posts: 4180
  • Gender: Male
  • Respect: +63
Re: Atlas NE-6 Caboose and Body-Mounted 2004 Couplers?
« Reply #2 on: November 15, 2013, 03:43:57 PM »
0
Quote from: Cory Rothlisberger on November 15, 2013, 02:33:13 PM
Uhh, we didn't use a special coupler on the NE-6. Did you try installing the Accumate?

I tried putting the Accumates on the smaller diameter, but it looked like the coupler shanks were higher than the boss. I was using my Opti-Visor at the time, and it seemed the Accumates would rub and not be able to turn from side to side properly. Still, I tried to fit them on, but then I couldn't coordinate holding the couplers in place while putting the lid back on. I got frustrated and... Anyhow, I followed Micro-Trains instructions to cut the bosses off so I can install the 2004 couplers I ordered. No going back now  :facepalm:

On the brighter side, I did buy another NE-6 caboose on eBay today (WITH Accumates installed), and I'm bidding on another caboose too.


Hmm... Kiz jumps the
gun again...

Logged
Two scientists create a teleportation ray, and they try it out on a cricket. They put the cricket on one of the two teleportation pads in the room, and they turn the ray on.
The cricket jumps across the room onto the other pad.
"It works! It works!"

bbussey

  • Crew
  • *
  • Posts: 9384
  • Gender: Male
  • Respect: +6187
    • www.bbussey.net
Re: Atlas NE-6 Caboose and Body-Mounted 2004 Couplers?
« Reply #3 on: November 15, 2013, 04:12:45 PM »
0
I wrote an article in the July/August 2005 N Scale Railroading that includes mounting MTL couplers on the NE6 caboose.
Logged
Bryan Busséy
NHRHTA #2246
NSE #1117
www.bbussey.net
Bridgeport & New London in N scale

Pages: [1]   Go Up
« previous next »