Author Topic: Tamiya Panel Liner  (Read 498 times)

0 Members and 1 Guest are viewing this topic.

SAH

  • Crew
  • *
  • Posts: 1309
  • Respect: +1963
Tamiya Panel Liner
« on: November 17, 2026, 02:37:50 PM »
0
Greetings to all you equipment weathering mavens.

I purchased the subject line items in a three pack:  Black, Brown and Gray.  I understand uses for black.  Under what conditions or for what intended effect would you use brown or gray?

Online tutorials suggest giving the model a gloss clear coat prior to applying the panel liner liquid.  Makes sense I suppose.  Does doing so match your application procedure?

Thanks,

Steve
Steve Holzheimer
Lakewood, OH
Modeling the AC&Y Spur 4 Serving the Tire Industry

thomasjmdavis

  • Crew
  • *
  • Posts: 4407
  • Respect: +1280
Re: Tamiya Panel Liner
« Reply #1 on: November 17, 2026, 03:38:31 PM »
0
From TamiyaUSA website panel line product page:
Quote
Examples of use:
Black is a general-purpose color and can be used for any type of model. Brown is great for military models as well as highlighting details on bright colors such as Yellow or Orange. Gray is perfect for White or Light Gray parts where Black may be too distinct.


Note:
Plastic parts may become brittle when using Tamiya Panel Line accent colors. Avoid using on movable parts and take care when applying to load-bearing areas. Apply over base coat of lacquer or acrylic paint. Accent Color paints may damage underlying base coat. Test before applying it onto the model. Take care when applying on flat base coat colors as Accent Color paints may permeate more readily.
Tom D.

I gave up rivet counting when I couldn't see an N scale rivet anymore.

peteski

  • Crew
  • *
  • Posts: 35450
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6700
    • Coming (not so) soon...
Re: Tamiya Panel Liner
« Reply #2 on: November 17, 2026, 03:47:01 PM »
0
Yes, black can be too stark in certain applications.
These are great for darkening diesel loco's (or other equipment) grilles.
. . . 42 . . .

Chris333

  • Crew
  • *
  • Posts: 19710
  • Respect: +6987
Re: Tamiya Panel Liner
« Reply #3 on: November 17, 2026, 04:10:25 PM »
0
I think these are enamel and leave a glossy finish. They work good though.

OrangeAnon

  • Crew
  • *
  • Posts: 62
  • Gender: Female
  • Respect: +65
Re: Tamiya Panel Liner
« Reply #4 on: November 17, 2026, 06:58:31 PM »
+4
These are great for darkening diesel loco's (or other equipment) grilles.

I haven't weathered any of my locos yet but I have done this (as well as other panel lines/details) and it really makes a huge difference.


Alexis W.

SAH

  • Crew
  • *
  • Posts: 1309
  • Respect: +1963
Re: Tamiya Panel Liner
« Reply #5 on: November 17, 2026, 08:33:37 PM »
0
Thanks @thomasjmdavis .  I did in fact read the factory info.  I was fishing for a "real life" example from among the community.

Exactly what I was hoping to see @OrangeAnon .  Thank you.  Your application was applied directly on the factory finish, correct?  Looks great and exactly like the effect I am trying to achieve.

The subject will be the Ann Arbor FA-2s I posted in the WE Update a couple of weeks ago.  I finished the detail work yesterday.  Fortunately I have a spare AA shell on which I can practice panel lining.
Steve Holzheimer
Lakewood, OH
Modeling the AC&Y Spur 4 Serving the Tire Industry

Westcoast_Trains

  • Crew
  • *
  • Posts: 76
  • Respect: +67
Re: Tamiya Panel Liner
« Reply #6 on: November 18, 2026, 12:33:07 AM »
0
I havent tried the grey or the brown yet, as i have found black to be the most useful. But i really enjoy the panel liner, great product. I prefer not to clear coat anything before weathering, personal preference. I usually do panel liner, then wash, then air brush, then powder or chalk last. I will do a light coat of clear after airbrushing and then again after adding powders or chalks. let it dry completely, then do one more coat of clear matte and call it done.

OrangeAnon

  • Crew
  • *
  • Posts: 62
  • Gender: Female
  • Respect: +65
Re: Tamiya Panel Liner
« Reply #7 on: November 18, 2026, 03:15:50 AM »
0
Your application was applied directly on the factory finish, correct?  Looks great and exactly like the effect I am trying to achieve.

Yes, but I'd be careful about doing this. It worked well on the Kato loco pictured, but I tried this on a ScaleTrains loco and the panel liner didn't flow as well and kind of spread outward into the finish. If you're not sure how it'll go, I'd apply a gloss coat first to ensure the panel liner flows well and stays where you want it.
Alexis W.

SAH

  • Crew
  • *
  • Posts: 1309
  • Respect: +1963
Re: Tamiya Panel Liner
« Reply #8 on: November 18, 2026, 12:24:02 PM »
0
Yes, but I'd be careful about doing this. It worked well on the Kato loco pictured, but I tried this on a ScaleTrains loco and the panel liner didn't flow as well and kind of spread outward into the finish. If you're not sure how it'll go, I'd apply a gloss coat first to ensure the panel liner flows well and stays where you want it.

Thanks for the heads up @OrangeAnon .  I do not own a ScaleTrains loco (true until the B&O GP30 shows up - some day) but I'll guess the finish tends toward matte compared with the Kato loco.  I think I'll spray the advised light clear coat first.

I havent tried the grey or the brown yet, as i have found black to be the most useful. But i really enjoy the panel liner, great product. I prefer not to clear coat anything before weathering, personal preference. I usually do panel liner, then wash, then air brush, then powder or chalk last. I will do a light coat of clear after airbrushing and then again after adding powders or chalks. let it dry completely, then do one more coat of clear matte and call it done.

My plan now is to clear coat, panel line, matte coat and then continue with my normal weathering routine:  dark over wash, highlights with either an air brush or pan pastels (or both) until I come up with something than looks like my AA No. 52 / 52A photos.  I've not found a need for a final clear coat once I switched to Pan Pastels.  Perhaps I don't handle my equipment often enough.

Thank you both for your help.
Steve Holzheimer
Lakewood, OH
Modeling the AC&Y Spur 4 Serving the Tire Industry

Sokramiketes

  • Crew
  • *
  • Posts: 5429
  • Better modeling through peer pressure...
  • Respect: +2198
    • Modutrak
Re: Tamiya Panel Liner
« Reply #9 on: November 18, 2026, 12:32:12 PM »
+1
Another thought, expecially since we're most likely to be applying to flat finished models...

Tube oil paint washes made with odorless mineral spirits does everything you're looking for and flows so well into crevices.  And the pigments are so fine, you don't get the large pigment spotting you sometimes get with model paint washes, especially acrylic model paint. 

And if it goes where you don't want it, a wet brush with spirits takes everything away.  So there's zero risk as you're learning. 

Point353

  • Crew
  • *
  • Posts: 3772
  • Respect: +928
Re: Tamiya Panel Liner
« Reply #10 on: November 18, 2026, 02:40:58 PM »
0
Tube oil paint washes made with odorless mineral spirits does everything you're looking for and flows so well into crevices.
And if it goes where you don't want it, a wet brush with spirits takes everything away.

Is that the Bob Ross method?

Chris333

  • Crew
  • *
  • Posts: 19710
  • Respect: +6987
Re: Tamiya Panel Liner
« Reply #11 on: November 18, 2026, 03:49:49 PM »
0
Night shift lightens the edges of pin washes with mineral spirits, but I have no idea what his pin wash is.

SAH

  • Crew
  • *
  • Posts: 1309
  • Respect: +1963
Re: Tamiya Panel Liner
« Reply #12 on: November 18, 2026, 08:01:34 PM »
+3
Dirt waits for no man.  That's the footer message for someone on here no?



I applied a light clear gloss coat.  Then used the panel liner on the chicken wire grills and air intake.  It behaved exactly as described and, as I hoped, flowed to the holes in the chicken wire grill.  As Mike pointed out, other materials can achieve the same effect of course.  My technique test bed is tipped on its side in the photo.

I then applied a tinted flat coat (light gray).  And since the airbrush was running nicely (I am a terrible air brush technician, so when the planets are aligned, keep rollin') I added mud splats and dusting to the areas the photos indicated.  Next will be pan pastels for highlights and the oil stains ALCOs were known for.  So far, so good.
Steve Holzheimer
Lakewood, OH
Modeling the AC&Y Spur 4 Serving the Tire Industry

robert3985

  • Crew
  • *
  • Posts: 3602
  • Respect: +2003
Re: Tamiya Panel Liner
« Reply #13 on: November 19, 2026, 08:17:28 AM »
0
I was getting ready to use my Black Tamiya Panel Line Accent Color on my brass Hallmark Geeps, which I painted years ago using Scalecoat 2, which is an enamel paint, and decided to read the instructions printed in micron-sized letters on the Panel Liner's label...AND, it says (in tiny letters) "Do not apply onto enamel paint."...the very first instruction.

Sooo...I asked Google Gemini if there would be a problem applying Panel Liner onto my ancient Scalecoat 2 Hallmark Geeps, noting that the paint had dried/cured for 20 years...and I got a DEFINITE NO...then Gemini proceeded to tell me exactly why and that how long the enamel paint had dried/cured, Panel Liner was not going to react kindly to it.

So, following recommendations, if you don't know what kind of paint (enamel, lacquer, acrylic, etc.) your model has been painted with, then a non-enamel clear coat over the top of it before using Panel Liner is probably very good advice.

Seems to me, IIRC, that Scale Trains uses Scalecoat 2, and maybe that explains why Panel Liner doesn't work very well with these fine models.

After consulting further with Gemini AI, it's apparent that even turpentine based artist's oil paints thinned with odorless paint thinner might very well have the same effect on a well-cured Scalecoat II surface.  I suggested that an acrylic craft paint (black) highly thinned with distilled water with just a touch of Dawn Dishwashing Liquid in it to act as a surfactant might work.  Gemini thought this was a good idea and offered another suggestion that instead of dishwashing liquid, that a minuscule dab of Jet-Dry would be a much better surfactant than Dawn.  Then Gemini also suggested substituting a drop or two of clear acrylic gloss medium for an equal amount of distilled water.

This is the recipe I'll try later today on the fans and dynamic brake grills on three of my Hallmark brass Geeps:

As a starting point and for a small amount of wash:
(1) - Mix ten drops of distilled water and one drop of black acrylic craft paint thoroughly
(2) - With a wooden toothpick, immerse about 1/8" of its tip into a bottle of Jet-Dry and swirl this very small amount into the well-mixed acrylic wash
(3) - ALTERNATE- (recommended)- Substitute 2 drops of acrylic gloss medium or Future Floor Wax for two drops of distilled water into the mix

How to test your wash before applying to your model:

White Styrene Test:
(1) - Score a scrap piece of white Styrene sheet with a several shallow cuts with an X-acto blade
(2) - Dip a fine paintbrush (size 0 or 00) into the wash and touch it to one end of the scored line you've made on the white Styrene
(3) - TOO THICK: If the wash doesn't immediately zip down the scored line on its own, it's too thick.  Add two drops of distilled water and test again, adding one or two drops of water until it immediately zips down on its own
(4) - TOO WEAK: If the wash zips down immediately, but appears grey rather than dark black, add a tiny dab of additional craft paint on the end of a toothpick, mix & test again until you get a shade that's appropriate for what you want.

After you've got the dilution, or shade of wash that you want, apply it to panel lines or grills by touching a loaded brush to the corner of a grill or fan recess or panel line, and let capillary action pull the wash into the recess.  Do not brush back and forth.  Waiting two or three minutes, wipe any surfaces you don't want the wash to cover by wiping with a wooden toothpick covered with a slightly damp lintless paper towel.  Wait too long, and the paint will be much harder to remove from the high surfaces.

At this point, this is purely informational, and I'll have practical application information later today or tomorrow.

The main advantage of this wash mixture is that it has a zero solvent risk...it won't react with commercial model paints (enamel, lacquer, acrylic, or such mixtures as Tru-Color Paint) because it contains no harsh solvent chemicals...just water, acrylic polymers and whatever is in Jet-Dry (which is used in dishwashers and dries with no residue).

Although I like Tamiya Panel Liner, and use it carefully on surfaces I know it won't adversely affect, if this acrylic craft paint wash works as well as I hope it does, I'll be using it quite a bit since many of my models are painted using Scalecoat II paint and other brands that might be adversely affected by the solvents in Panel Liner.

Cheerio!
Bob Gilmore

 

Sokramiketes

  • Crew
  • *
  • Posts: 5429
  • Better modeling through peer pressure...
  • Respect: +2198
    • Modutrak
Re: Tamiya Panel Liner
« Reply #14 on: November 19, 2026, 02:15:41 PM »
0
Night Shift adapts his pin washes to the base paint, but does use Tamiya and AK versions.  I remember him saying a couple things about it, or that "enamel will work good in this case" but probably didn't pay enough attention to reiterate his thoughts.

Here's what I do know from experience.  Every time I try to do a quick grill darkening at the bench with acrylic, I'm mad that I didn't bring out the Oil Paints.  And yes, even knowing how good they work it feels like an extra step to drag out a tube, get the odorless mineral spirits out, etc.  And that bottle of Polly Scale black, or Testors acrylic black or even craft paint is just hanging out right there and I have water out for cleaning brushes, and, and, maybe it will be good just this one time.

And then every time that acrylic paint settles out into tiny polka dots on me. 

And every time I get over the hump and use oil paint washes, its perfect flow and consistent darkening. 

Maybe its a surface tension thing and some flotrol or dish soap helps.  And Rich Yourstone certainly proved he could manipulate acrylics perfectly too.  I have some examples and they don't show the issue up close.

But I'm not good at it and know what does work better for me.  (And I haven't had odorless mineral spirits attack any finish acrylic, enamel, or lacquer.  Including TruColor (which is what Scale Trains briefly advertised they were using, or could at least be used for modeler touch up)