Author Topic: Atlas RS2 Loksound install (n scale)  (Read 405 times)

0 Members and 1 Guest are viewing this topic.

PanAmShay

  • Crew
  • *
  • Posts: 88
  • Respect: +39
Atlas RS2 Loksound install (n scale)
« on: November 06, 2026, 06:05:29 PM »
0
I have a 2020 run Atlas RS2 that I am planning to install a Loksound 58781 (Kato SD90) decoder. 

Does anyone know why the factory would have put electrical tape over the LEDs and wrap it down around the frame? 

I'm glad Spookshow mentions how difficult it is to remove the shell on these, otherwise I might have given up.  It seems like the shell wouldn't be so tight w/o the electrical tape and it doesn't seem to be insulating anything.  I test fit a 58781 decoder from another loco and it fit well in the frame and ran on my track w/o issue, so hoping I can find room the speaker

DC chassis as shipped by the factory:
[ Guests cannot view attachments ]

nickelplate759

  • Crew
  • *
  • Posts: 3885
  • Respect: +1662
Re: Atlas RS2 Loksound install (n scale)
« Reply #1 on: November 06, 2026, 06:17:41 PM »
0
The tape is likely intended a a light block for the headlights.
George
NKPH&TS #3628

I'm sorry Dave, I'm afraid I can't do that.

PanAmShay

  • Crew
  • *
  • Posts: 88
  • Respect: +39
Re: Atlas RS2 Loksound install (n scale)
« Reply #2 on: November 06, 2026, 06:29:26 PM »
0
Thanks George, that was one of my guesses, but most other DC boards I've received come with a bit of shrink-wrap around the LED instead.  Wanted to make sure I wasn't missing something...

MK

  • Crew
  • *
  • Posts: 4371
  • Respect: +956
Re: Atlas RS2 Loksound install (n scale)
« Reply #3 on: November 06, 2026, 06:45:34 PM »
0
That's so ghetto, blocking the LED light like that!    :o

(Though it would be tough to put a shrink wrap around a SMD LED.)

peteski

  • Crew
  • *
  • Posts: 35434
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
Re: Atlas RS2 Loksound install (n scale)
« Reply #4 on: November 06, 2026, 06:57:12 PM »
0

Atlas used to use shrink wrap over the LEDs some time in the past.  I guess now anything goes.  :facepalm:  No the best solution.   In some models they paint the inside of the body silver or black, or both.

Does the extra thickness of the tape over the chassis make it more difficult yo remove the shell?  Um, I found the answer to that: https://spookshow.net/loco/llrs2.html
. . . 42 . . .

PanAmShay

  • Crew
  • *
  • Posts: 88
  • Respect: +39
Re: Atlas RS2 Loksound install (n scale)
« Reply #5 on: November 06, 2026, 07:22:33 PM »
0
MK, these are classic 3mm dia thru hole LEDs--shrinkwrap would have been easy.  But apparently not as easy as the tape, which made the chassis all gummy.   :facepalm:

Peteski, yes, I thought I mentioned, the shell is a complete PITA to remove. A tiny screwdriver thru the truck to separate the shell from one side of the frame at the bump, an angled pick on the other side, and then pry out with a third screwdriver.  Repeat for other side.  Curse when you realize you might have damaged one of the handrails.   :x

I'm hoping it is a lot easier w/o the tape, but will wait until I have the decoder installed to find out...

BTW, did you ever do a schematic of the 58781 Kado SD90 Loksound decoder

peteski

  • Crew
  • *
  • Posts: 35434
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
Re: Atlas RS2 Loksound install (n scale)
« Reply #6 on: November 06, 2026, 09:21:21 PM »
0
MK, these are classic 3mm dia thru hole LEDs--shrinkwrap would have been easy.  But apparently not as easy as the tape, which made the chassis all gummy.   :facepalm:

Peteski, yes, I thought I mentioned, the shell is a complete PITA to remove. A tiny screwdriver thru the truck to separate the shell from one side of the frame at the bump, an angled pick on the other side, and then pry out with a third screwdriver.  Repeat for other side.  Curse when you realize you might have damaged one of the handrails.   :x

I'm hoping it is a lot easier w/o the tape, but will wait until I have the decoder installed to find out...

BTW, did you ever do a schematic of the 58781 Kado SD90 Loksound decoder

Yes, electrical tape adhesive gets all melty, especially when some of the mechanism lubricants get on it.  This is not the first model (from various manufacturers, except Kato) using electrical tape. BLI is another offender.  :(

And yes you did mention having trouble removing the shell but my brain sometimes glosses over things.  :facepalm:

I'm surprised that a Kato outline decoder fits the Atlas model.  ESU first came out with the narrow body Kato decoder 58741. Then they made 58771 and 58781. Basically they are the same decoder with the board having slightly different shape and component layout.  My writeup for 58741 is about 90% done. I'm not sure if I'll buy the other two decoders to do writeups on them, but as I mentioned they are almost identical.

If you were to remove the tape from the model with the Atlas board still installed, I would be curious about how bad is the light leak through the body shell. Maybe that tape was not really needed after all?
. . . 42 . . .

MK

  • Crew
  • *
  • Posts: 4371
  • Respect: +956
Re: Atlas RS2 Loksound install (n scale)
« Reply #7 on: November 06, 2026, 09:43:45 PM »
0
MK, these are classic 3mm dia thru hole LEDs--shrinkwrap would have been easy.  But apparently not as easy as the tape, which made the chassis all gummy.   :facepalm:

Duuuuh, of course!  It's a 2020 loco so no SMD (not 100% sure) back then.   :facepalm:

Would it be easy then to just remove the tape and shrink wrap the 3mm LED yourself?

PanAmShay

  • Crew
  • *
  • Posts: 88
  • Respect: +39
Re: Atlas RS2 Loksound install (n scale)
« Reply #8 on: November 06, 2026, 09:49:59 PM »
0
MK--sorry I wasn't clear in my original post.  I am converting from DC to DCC, so will remove the DC light board.  I've cut the frame to make room for a speaker and will install an ESU Loksound 58781. I will shrink-wrap the LEDs on that.  I just didn't want to not install the tape if there was some other reason I'm not aware of that it was needed.

BTW, the axle wipers on these are the shiniest brass ever!  I don't know why they stood out so much, but I felt it was necessary to disassemble the trucks and paint the visible portions of the axle wipers.  I don't think I've noticed this so badly on other locos before.

peteski

  • Crew
  • *
  • Posts: 35434
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
Re: Atlas RS2 Loksound install (n scale)
« Reply #9 on: November 06, 2026, 10:40:41 PM »
0
Duuuuh, of course!  It's a 2020 loco so no SMD (not 100% sure) back then.   :facepalm:

Would it be easy then to just remove the tape and shrink wrap the 3mm LED yourself?

If he replaces the board with the ESU decoder then that is a moot point.  That decoder has small on-board SMD headlight LEDs, but also a place to solder standard 3mm LEDs. He could just take the LEDs from the atlas board (or get new LEDs) then heat-shrink tubing over them.  Those solder-in "headlight" LED locations are actually AUX outputs, so they need to be remapped to become headlights.

That brings up another point. ESU does include a pair of warm white 3mm LEDs with the decoders, but to me ESU LEDs do not look like incandescent bulbs. Light is too yellow. The original Atlas LEDs might be a better representation of the incandescent bulb light.
. . . 42 . . .

cgw

  • Crew
  • *
  • Posts: 195
  • Respect: +42
Re: Atlas RS2 Loksound install (n scale)
« Reply #10 on: November 07, 2026, 02:50:16 AM »
0
how did you modify the frame for the speaker ?   and which brand/model of speaker did you use in this application?

garethashenden

  • Crew
  • *
  • Posts: 2352
  • Respect: +1854
Re: Atlas RS2 Loksound install (n scale)
« Reply #11 on: November 07, 2026, 06:55:58 AM »
0
I'm surprised that a Kato outline decoder fits the Atlas model.  ESU first came out with the narrow body Kato decoder 58741. Then they made 58771 and 58781. Basically they are the same decoder with the board having slightly different shape and component layout.  My writeup for 58741 is about 90% done. I'm not sure if I'll buy the other two decoders to do writeups on them, but as I mentioned they are almost identical.

I'm not that surprised. A lot of Life-Like locomotives take decoders with those wide vertical contacts.

PanAmShay

  • Crew
  • *
  • Posts: 88
  • Respect: +39
Re: Atlas RS2 Loksound install (n scale)
« Reply #12 on: November 07, 2026, 09:42:46 AM »
0
how did you modify the frame for the speaker ?   and which brand/model of speaker did you use in this application?

CGW, I cut down the front of the frame (long hood forward), taping the frame halves together and then clamping just the front (avoiding the shell retaining bumps) in a smooth jawed vice.  I would have preferred using a manual milling machine, but don't readily have access to one at home, so used a thin kerf modeling saw (probably designed for plastic).  I made a mistake and made the first cut too low, which is why there is a notch right before the clip on brass bearing retainer.  No harm, just slight loss of weight, which I can add back in.  This was only my third time modifying a frame like this, so I'm still learning.  The first two were a pair of GP-40 (which took the Loksound Atlas legacy boards) that I did a few weeks ago.  I would accept recommendations for a thin kerf metal cutting saw--a normal hacksaw blade is not great for this. 

On speakers, I hope to fit an ESU 50342 9x16 speaker.  I fit these in the GP-40 mentioned above, but those had a bit more room between the frame and the underside of the decoder.  I sanded down the smallest speaker box by hand on those, both for height and for width.  If I can't fit that, I should be able to fit a SP-1508 from Digikey.  It is 15x8 and a little bit thinner.  I'll report back once that is installed. 


[ Guests cannot view attachments ]


« Last Edit: November 07, 2026, 09:44:26 AM by PanAmShay »

peteski

  • Crew
  • *
  • Posts: 35434
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
Re: Atlas RS2 Loksound install (n scale)
« Reply #13 on: November 07, 2026, 11:34:00 AM »
0
That looks like a ZONA razor saw. It is not just for plastic, It is pretty hard steel and (as you experienced) should have no problem cutting soft white metal.  I sometimes use it to cut brass, but wouldn't want to use to try cutting something like music wire or a drill bit shank.  :)

You sure did a nice job making a smooth and straight cut.  As for clamping frame halves in a vise, you can put pieces of plywood between the shell and vise jaws.  The typical low-grade plywood material is soft enough to dent where the shell locking bumps are, and will allow you a more secure mounting of the frames.  I use small pieces of Luan plywood. It is a soft wood.
. . . 42 . . .

Sumner

  • Crew
  • *
  • Posts: 901
  • Gender: Male
  • Respect: +2510
    • My Home Pages....
Re: Atlas RS2 Loksound install (n scale)
« Reply #14 on: November 07, 2026, 12:03:05 PM »
0
Quote
I would accept recommendations for a thin kerf metal cutting saw--a normal hacksaw blade is not great for this.

Not saying this will be better or worst but I use the same jeweler's saw and blade that I use to cut isolation cuts in the rails of hand-laid turnouts.





More information on cutting frames with the saw here.....

https://1fatgmc.com/RailRoad/Decoder-1/page-16.html

Sumner
« Last Edit: November 07, 2026, 12:28:37 PM by Sumner »
Working in N Scale ---Modeling UP from late 40's to early 70's very loosely......

Under$8.00 Servo turnout Control --- 3D Printed Model RR Objects -- My Home Page

http://1fatgmc.com/RailRoad/RR Main/Link Page Menu.html