Author Topic: Skytop: Installing DCC and accurate tail light function Hiawatha Kato N scale  (Read 7266 times)

0 Members and 1 Guest are viewing this topic.

Point353

  • Crew
  • *
  • Posts: 3772
  • Respect: +928
0
The RGB LEDs are available configured either as common-anode or common-cathode, or with independent/isolated connections for each color to suit your needs.

mmagliaro

  • Crew
  • *
  • Posts: 6505
  • Gender: Male
  • Respect: +2014
    • Maxcow Online
0
You can get surface mount LEDs that are 2-color, white and red.
http://www.mouser.com/ds/2/216/AAA3528QWDSURKS-52552.pdf

peteski

  • Crew
  • *
  • Posts: 35440
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
+2
My plan (when I get to it) is to totally re-do the lighting (including the table lamps).  I will discard most of the stock lighting equipment.  Small red LEDs will be installed in the side marker lenses (and I'll get rid of the thick clear channels on the inside of the car.  I will make a new clear center lens and install a red/white LED in to (again getting rid of the light-conduit).

I have installed working table lamps back in 1991 in a N&W Powhatan Arrow observation car. Back then I used fiber optics and a shade made on lathe-turned milky-colored acrylic (to diffuse the light).  But nowadays I'm thinking of using 3D printed shades and installing 0201 LEDs in each lamp.





As far as function-only decoder goes, I tried Digitrax and NCE, but now I prefer ZIMO.   I buy Zimo MX681N (because it is the cheapest) and add my own wires.  It is a tiny 6-function decoder.
. . . 42 . . .

u18b

  • Crew
  • *
  • Posts: 4057
  • Respect: +2388
    • My website
0
Here is the simple board I will design.
T shaped channels separate areas.

Big area on left is positive.

So I will solder two 0402 LEDs.  One white and one red.

The decoder wires in the drawing are symbolic.
In reality, I will use magnet wire.  Decoder wires are too fat.

« Last Edit: January 24, 2024, 04:49:29 PM by u18b »
Ron Bearden
CSX N scale Archivist
http://u18b.com

"All get what they want-- not all like what they get."  Aslan the Lion in the Chronicles of Narnia by C.S.Lewis.

peteski

  • Crew
  • *
  • Posts: 35440
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
0
Ron,
as it was mentioned, you should be able to buy a red/white LED with both LED dies in a single SMD package.  But I'm sure it woudl cost more than using individual LEDs you might already have.
. . . 42 . . .

u18b

  • Crew
  • *
  • Posts: 4057
  • Respect: +2388
    • My website
0
Ron,
as it was mentioned, you should be able to buy a red/white LED with both LED dies in a single SMD package.  But I'm sure it woudl cost more than using individual LEDs you might already have.

Yeah.  I'm going to go with what I have...

But I envision this thread not simply me doing this.

I hope a lot of others will too.
And share ideas and photos.

Ron Bearden
CSX N scale Archivist
http://u18b.com

"All get what they want-- not all like what they get."  Aslan the Lion in the Chronicles of Narnia by C.S.Lewis.

u18b

  • Crew
  • *
  • Posts: 4057
  • Respect: +2388
    • My website
0
On the underside of the car, Kato placed an access hatch just like they did on one of the CZ cars.



A small screwdriver can carefully pry it open.



Sorry for the fuzzy pic.

From here we have access to the contacts for the red and black track wires for the decoder.




After a lot of experimentation, I decided to hide the decoder in the toilet- or whatever that tank is.

The only problem is that I need to remove that one brace.   A motor tool with a small bit did the job well.




These are pics for reference later.

I'm using a Digitrax DZ126T (white wrapper).
I took the wrapper off so I could re-wire it (I'm pretty sure that voids the warranty   :ashat: ).

Black and red are the only wires on this side.




And all the rest are on this side.  I removed them all.




And here's my note for how they go back.
In some cases, I'll be using thin magnet wire.
Also, a bulb will be soldered at the gray and orange wires.








Ron Bearden
CSX N scale Archivist
http://u18b.com

"All get what they want-- not all like what they get."  Aslan the Lion in the Chronicles of Narnia by C.S.Lewis.

peteski

  • Crew
  • *
  • Posts: 35440
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
0
If you are planning on using a light bulb (I assume for electric load) it might get hot when the speed is cranked up. Yes, you can set the speed table to very low speed (low average voltage) but if those CV settings get accidentally modified (without you realizing it) and the light bulb is near plastic parts then you can have some melting and damage. I realize that this is unlikely to occur, but I would not take a chance.

I assume you are doing this so you can read the CVs back from the decoder. You might want to consider adding a cut-out switch for the bulb and only engage it while programming.
. . . 42 . . .

u18b

  • Crew
  • *
  • Posts: 4057
  • Respect: +2388
    • My website
0
That's a good idea.  I think I will add a switch.

Thx.
Ron Bearden
CSX N scale Archivist
http://u18b.com

"All get what they want-- not all like what they get."  Aslan the Lion in the Chronicles of Narnia by C.S.Lewis.

mmagliaro

  • Crew
  • *
  • Posts: 6505
  • Gender: Male
  • Respect: +2014
    • Maxcow Online
0
Illuminated lampshades inside a passenger car?

Congratulations, Ron!  I nominate you for the "Model Railroading Insanity Award - 2017"   :D

OUCH.  My mistake.  PETE... YOU are nominated for MRIA-2017.   :D
I just didn't look at the name on that post correctly.  Sorry!


« Last Edit: November 16, 2017, 10:13:03 PM by mmagliaro »

u18b

  • Crew
  • *
  • Posts: 4057
  • Respect: +2388
    • My website
0
Max.

Please correct.

That was Pete!
Ron Bearden
CSX N scale Archivist
http://u18b.com

"All get what they want-- not all like what they get."  Aslan the Lion in the Chronicles of Narnia by C.S.Lewis.

Lemosteam

  • Crew
  • *
  • Posts: 6469
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5029
0
Illuminated lampshades inside a passenger car?

Congratulations, Ron!  I nominate you for the "Model Railroading Insanity Award - 2017"   :D

Seriously, that is AMAZING.  The ones you did with the fiber optic tube look excellent!   But I have to question whether
it is really worth the complexity of wiring all those 0201 SMD LEDs in there.   Do you expect that to be easier than using
fiber optics?

I. Simply. Can't. Downvote. Max.    :trollface: :trollface: :trollface: :D :D :D  it's still early on the west coast!
John "Lemosteam" LeMerise

u18b

  • Crew
  • *
  • Posts: 4057
  • Respect: +2388
    • My website
0
This is my test setup.
Loco chassis just sits on layout while I run lights.




This is a circuit board that came out of a Kato 11-105 B unit chassis (I think).
I cut an extra trench or two.

LEDs are TINY!  Macro photo is deceptive.



If I can get it to work, I would trim all of that down to a couple of mm.  The board just around the LEDS.

This is what I have in mind if I can get my parts to work.

Forward:  red Mars light.


Reverse:  white (a little blue-ish, but I would add Tamiya paint later to soften it.)



At present, white LED fails at 6k.  I'll go a little higher, but I think they are a bust.
I'll see what else I have.

Right now just letting red run continuously seeing if I can burn it out.

Ron Bearden
CSX N scale Archivist
http://u18b.com

"All get what they want-- not all like what they get."  Aslan the Lion in the Chronicles of Narnia by C.S.Lewis.

mmagliaro

  • Crew
  • *
  • Posts: 6505
  • Gender: Male
  • Respect: +2014
    • Maxcow Online
0
I. Simply. Can't. Downvote. Max.    :trollface: :trollface: :trollface: :D :D :D  it's still early on the west coast!

I really am sorry.  I corrected the orginal post.
PETE is my nominee for  MRIA 2017.

(And Ron... this project is still wonderful... in spite of my careless gaff).

peteski

  • Crew
  • *
  • Posts: 35440
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
0
I really am sorry.  I corrected the orginal post.
PETE is my nominee for  MRIA 2017.

(And Ron... this project is still wonderful... in spite of my careless gaff).

Thanks Max!  It actually took a first place in the passenger car category a the National Convention in Denver (IIRC, it was in 1991).   8)
That car has the side markers illuminated with 0.010" fiber optics, illuminated Tomar drumhead, interior lighting, and illuminated table lamps. The power is supplied from the track, but it first goes to what we nowadays call a "keep-alive" circuit which uses a small NiCad battery hidden in the kitchen area to supply the power to the light bulbs (not LEDs) when the track power is lost.

As far as why to use LEDs instead of fiber optics in the table lamps? Just to see if I can do it.  :) But I'm flexible - I might rethink this.  I used 0.020" fiber optics for those lights (the fiber is painted gold and doubles as the lamp base/stem).  It looks a bit too bulky.  If I squeeze the LED into the shade then I can use the twisted magnet wire leads as a stem. Much thinner.  But if I used a 0.010" fiber optic instead, that might not be bad.  Thanks for pointing it out - I'll have think about this some more.

Ron: sorry for this blatant thread hijack.  :oops:  I just wanted to show what I am planning to do in my OH observation car.

What do you mean that the LED fails at 6k?  It burns up with 12V applied to it through a 6k resistor?!
« Last Edit: November 16, 2017, 11:31:55 PM by peteski »
. . . 42 . . .