Author Topic: The Carolina Sandhills Lines in HO Scale  (Read 456588 times)

0 Members and 2 Guests are viewing this topic.

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3570 on: October 30, 2026, 09:24:33 PM »
+6
The only thing I would maybe address again is the streaks of grime on the sides of the long hood; right at the roof line it smudges up, to where the very top is narrower than the grime streak. I’d take your applicator, start it on the roof, and drag it around and down that first little bit to simulate the way rain is going to pool along the edge then wash down.

I went back and deleted the soot streaks on the long hood.  I tried plain water to minimize the damage to the weathering, but, ultimately, it took soapy water and Q-tips to scrub the area sufficiently to get rid of the ”soot” before I could finish the weathering. 

I want to leave the middle of the long hood a little lighter on the dirt, because the prototype seems to be dirtiest towards the ends of the locomotive.  I’m cool with it now.



DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

Iain

  • Crew
  • *
  • Posts: 4908
  • Gender: Female
  • Na sgrìobhaidh a Iain
  • Respect: +849
    • The Best Puppers
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3571 on: October 30, 2026, 11:00:19 PM »
+1
I went back and deleted the soot streaks on the long hood.  I tried plain water to minimize the damage to the weathering, but, ultimately, it took soapy water and Q-tips to scrub the area sufficiently to get rid of the ”soot” before I could finish the weathering. 

I want to leave the middle of the long hood a little lighter on the dirt, because the prototype seems to be dirtiest towards the ends of the locomotive.  I’m cool with it now.



DFF

<peer pressure> Now make the tank smaller.  If I can do it in N, you can do it in HO </peer pressure>
I like ducks



davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3572 on: October 30, 2026, 11:37:28 PM »
+1
<peer pressure> Now make the tank smaller.  If I can do it in N, you can do it in HO </peer pressure>

I’ve already looked into that.  It would require milling the metal frame to get that open area between the fuel tank and the rear truck.  I’d have to completely tear the locomotive down to the frame to do that.  Am I capable of doing that?  Yes.  Am I going to do that?  No, too invasive at this point.

DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

packers#1

  • Crew
  • *
  • Posts: 1640
  • Gender: Male
  • Modern Shortline Modeler
  • Respect: +924
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3573 on: October 31, 2026, 10:55:46 AM »
+1
I went back and deleted the soot streaks on the long hood.  I tried plain water to minimize the damage to the weathering, but, ultimately, it took soapy water and Q-tips to scrub the area sufficiently to get rid of the ”soot” before I could finish the weathering. 

I want to leave the middle of the long hood a little lighter on the dirt, because the prototype seems to be dirtiest towards the ends of the locomotive.  I’m cool with it now.



DFF

I don’t think they needed to get all the way deleted, but now that they’re gone it definitely looks more like the prototype photo. Great job!
Sawyer
American manufacturing isn’t dead, it’s just gotten high tech

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3574 on: November 01, 2026, 12:48:12 PM »
0
I don’t think they needed to get all the way deleted, but now that they’re gone it definitely looks more like the prototype photo. Great job!

Thanks, Sawyer!

DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3575 on: November 01, 2026, 01:12:32 PM »
+4
I went to the Timonium show yesterday, keeping the budget at $200.  I came home with these items:



Atlas CRR GP38 with DCC: $95.00
Rapido PC X72 boxcar: $40.00
Athearn PC caboose: $15.00!
Oxford Models 1960 Ford Ranchero: $19.90
Oxford Models 1965 Plymouth Barracuda: $15.00

GRAND TOTAL: $184.90.  Including the lunch I grabbed at the show, I came home with $2.10. 🤣  Most enjoyable and fruitful show for me in a long time.

I was up until 3:30 a.m. (including gaining an hour with the Daylight Saving Time ending) gutting the CRR GP38 and adding a Decoder Buddy, LokSound V5.0 decoder, and LED lights.  Please ignore the excess wire length to the rear LED.  That was intentional, because the plan is to eventually add a Scale Sound Systems speaker, and I’m allowing for re-routing the wires.  The speaker installed last night was just grabbed from my pile of decommissioned speakers from other projects that already received their Scale Sound Systems speaker.



I reprogrammed the Geep, and, this morning, I broke it in and speed matched it to fleet standards.  Here it is with CRR F7A No. 813.  (Interesting that some of the proto photos on rrpicturearchives.net include both of these locomotives in the same picture.)  Why Clinchfield on this Seaboard layout?  Well, the SCL interchanged directly with the CRR in North Carolina, and many a CRR locomotive made it to Hamlet and then was diverted all the way up to Richmond, Va. along the line that I model.  Foreign power from CRR, Frisco, and even Southern Pacific were often seen in North Carolina.



DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

Dave V

  • Crew
  • *
  • Posts: 12424
  • Gender: Male
  • Foothills Farm Studios -- Dave's Model Railroading
  • Respect: +12072
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3576 on: November 01, 2026, 01:34:52 PM »
+2
And now that you're a weathering expert, you're gonna have a blast with that PC boxcar!

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3577 on: November 01, 2026, 01:46:17 PM »
+2
And now that you're a weathering expert, you're gonna have a blast with that PC boxcar!

Not really.  The date on that car is 1-72 (January 1972), so that just squeaks into the tail end of my 1970-72 era.  It’s brand spanking new.  Ed and I discussed this yesterday, and he suggested a light dusting.

That said, I have two PRR X58B boxcars and a PC G43C gondola that will need the Penn Central treatment. :D

Thanks,
DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

Dave V

  • Crew
  • *
  • Posts: 12424
  • Gender: Male
  • Foothills Farm Studios -- Dave's Model Railroading
  • Respect: +12072
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3578 on: November 01, 2026, 02:48:40 PM »
+2
Not really.  The date on that car is 1-72 (January 1972), so that just squeaks into the tail end of my 1970-72 era.  It’s brand spanking new.  Ed and I discussed this yesterday, and he suggested a light dusting.

That said, I have two PRR X58B boxcars and a PC G43C gondola that will need the Penn Central treatment. :D

Thanks,
DFF

That's the beauty of pan pastels... Layers and control. Then I would suggest weathering the trucks and couplers, a hint of road grime on the lower half of the ends, and maybe a little grime around the lower part of the door and door track. A few very subtle hints of new rust on that silver roof.
« Last Edit: November 01, 2026, 02:54:16 PM by Dave V »

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3579 on: November 01, 2026, 08:39:28 PM »
0
That's the beauty of pan pastels... Layers and control. Then I would suggest weathering the trucks and couplers, a hint of road grime on the lower half of the ends, and maybe a little grime around the lower part of the door and door track. A few very subtle hints of new rust on that silver roof.

Agreed and will do.  I’ve got a couple of locomotives in the queue to do first, and I think I want to practice on that Atlantic & Danville boxcar I bought a few weeks ago when I try my hand on the first freight car.

DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3580 on: November 02, 2026, 05:51:56 PM »
+5
I weathered another locomotive- SCL GP18 No. 1063.  There’s only one thing unweathered in this photo.  Can you find it? 🤣



DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3581 on: November 03, 2026, 10:41:34 PM »
+5
The NS still served the Talbird Sand Company’s sand pit on its Aberdeen Line into the 1970s (the last active shipper of sand on this branch), so I changed some coal loads that I previously made with black art sand. 

Before:



Since I used white glue to secure the “coal,” I soaked the loads in wet water for an hour or two.  Most of the sand just fell off in the bath, and a little scrubbing in the laundry tub took care of the rest.  I still have a box of a sandy colored unsanded grout, so I applied that to the stripped load.  I’ll come back and weather these cars at some point to show them in sand service.  I also have an SCL hopper that may receive the same treatment, as the SCL was a source of empty open hoppers for NS.  I just haven’t confirmed whether the SCL was providing its own cars or just returning NS’s hoppers.

After:



DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3582 on: November 05, 2026, 08:35:37 PM »
+4
The next weathering victim, SCL F7A No. 405:



Here’s the “before” and “after” . . . in the same pic! 😉



DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3583 on: November 07, 2026, 12:54:37 AM »
+4
A little more weathering this evening on a B&O boxcar.  I added the last two Tangent train line hoses that I have and then used Pan Pastels.  What a difference a few details, such as Sergent Engineering couplers, Kadee wheelsets, and the air hoses make to an inexpensive Accurail boxcar.





It ain’t much of one, but I do technically now have an entire weathered train:



DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8803
Re: The Carolina Sandhills Lines in HO Scale
« Reply #3584 on: November 08, 2026, 12:32:15 AM »
+1
This Atlantic & Danville (A&D) boxcar met the Pan Pastels this afternoon.  Unfortunately, the weathering on this car doesn’t seem to show as well in photos as it does in person.  That said, as my weathering skills improve, I’ll probably come back and hit this one harder, because by the early 1970s, the A&D had been liquidated at auction.  The winning (and only) bidder, the N&W, took over the A&D in 1962, operating it as the Norfolk, Franklin, and Danville (NF&D).





DFF
« Last Edit: November 08, 2026, 12:42:27 AM by davefoxx »

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies