Author Topic: Replacement for ER Sharknose motor?  (Read 242 times)

0 Members and 1 Guest are viewing this topic.

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Replacement for ER Sharknose motor?
« on: Yesterday at 11:48:55 AM »
0
In cleaning my coal drag train for the club Open House season, I found one of my ER Sharknose units running hot, and can see randomly intermittent big sparks from the motor after removing the shell.  And I can see a deposit of loose black stuff on the frame under the motor brush area.

It still runs pretty well, though.

So, I am guessing that the armature wiring is OK but the brushes are shot.

Any suggestions for sources of new motor or brushes for the old motor?


Showme

  • Crew
  • *
  • Posts: 83
  • Respect: +40
Re: Replacement for ER Sharknose motor?
« Reply #1 on: Yesterday at 01:51:28 PM »
0
  Many years ago, I was doing a lot of custom painting for the original founder of J&J Trains. He was taking the very first runs of the Atlas GP-9's and GP-30's and installing a Kato motor in them. Dumped the old three pole motors. No flywheels back then, but it certainly made a difference in how they ran. Would glue the motor in with a dab of silicone caulk. I still have several of those just for old times' sake and they still do the job.

Bob

peteski

  • Crew
  • *
  • Posts: 35444
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6698
    • Coming (not so) soon...
Re: Replacement for ER Sharknose motor?
« Reply #2 on: Yesterday at 09:32:31 PM »
0
The commutator's gaps might just be filled with oily brush dust.  If there is an access to the commutator, that could be cleaned out.

Wasn't the mechanism made by Bachmann?  Does it use a Bachmann open-frame motor?  I have bunch of those.
« Last Edit: Yesterday at 09:36:40 PM by peteski »
. . . 42 . . .

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Replacement for ER Sharknose motor?
« Reply #3 on: Yesterday at 10:42:10 PM »
0
It is a 5-pole motor with dual flywheels.  See review at https://www.spookshow.net/loco/euroshark.html

I have not yet taken any of the motors out of my ER locos, so I am not really clear on how they are configured.  Their electrical connections in the ER locos is with a pair of springy strips from the board to the brush holders, so replacement with something else would require soldered wires and probably also some sort of different mount. 

Given the amount of "oily dust" I am seeing, I think the brushes must be pretty badly worn.  So, are there likely to be replacements for the brushes if I can figure how to clean the commutators?

peteski

  • Crew
  • *
  • Posts: 35444
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6698
    • Coming (not so) soon...
Re: Replacement for ER Sharknose motor?
« Reply #4 on: Yesterday at 10:53:05 PM »
0
Yes, Spookshow. Duh!


That looks like standard Bachmnn mtor. I have bunch but I think they are 3-pole. Brushes should be the same.  I would give your motor a good bath in Naphtha and I suspect that the brushes still have plenty of life in them.  I guess I could send you a pair too.
. . . 42 . . .

u18b

  • Crew
  • *
  • Posts: 4057
  • Respect: +2388
    • My website
Re: Replacement for ER Sharknose motor?
« Reply #5 on: Today at 12:12:43 AM »
0
I don't know what this one is....

But Bachman did make a small square motor that was 5-pole (and skew wound).   It was in the Spectrum C40-8.   They are great motors.

Spook:  https://www.spookshow.net/loco/files/bachdash8mechold.jpg
Ron Bearden
CSX N scale Archivist
http://u18b.com

"All get what they want-- not all like what they get."  Aslan the Lion in the Chronicles of Narnia by C.S.Lewis.

Point353

  • Crew
  • *
  • Posts: 3772
  • Respect: +928
Re: Replacement for ER Sharknose motor?
« Reply #6 on: Today at 01:25:29 AM »
0
I don't know what this one is....

But Bachman did make a small square motor that was 5-pole (and skew wound).   It was in the Spectrum C40-8.   They are great motors.

Spook:  https://www.spookshow.net/loco/files/bachdash8mechold.jpg

There's a post on facebook from six months ago which describes replacing a sharknose motor with one for a dash 8.
The flywheels are different sizes and the motor shafts are different lengths, so the flywheels need to be pulled and swapped and the driveshafts on the dash 8 motor cut to match the length of those on the sharknose motor.

peteski

  • Crew
  • *
  • Posts: 35444
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6698
    • Coming (not so) soon...
Re: Replacement for ER Sharknose motor?
« Reply #7 on: Today at 08:53:22 AM »
0
I checked mine and the brushes are 1.5mm diameter and around 3mm long, if you want to check how your brushes are.

Going back to the motor, those are very simple devices. Electrically there isn't much there to go bad.  Smoking and sparking could definitely be caused by the oily brush dust getting burned by the sparking which occurs at the commutator.  This is often the case in N scale models which are almost always seriously over-lubricated at the factory.  Thoroughly cleaning (and re-lubricating) the motor would be the quickest, easiest and cheapest thing to try. Really.

These more recent Bachmann motors (especially the 5-pole) are actually pretty decent.
. . . 42 . . .

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Replacement for ER Sharknose motor?
« Reply #8 on: Today at 12:52:38 PM »
0
Thanks all for the relies.

My schedule at the moment does not allow addition of the task for pulling this motor, so the project is going on the shelf until after Thanksgiving and the Open House the immediately following weekend.

I would like to simply refurb this motor.  At the moment, I have swapped its shell for another mechanism that will be running during Open House.  But, I don't have any more backup mechanisms if another fails.  The lashup for Open House is 4 of these units (ABBA) and they need to be carefully checked for running at about the same speed when going in the TRAIN's forward direction.  It is surprising how much difference in speed occurs between directions for single locos as well as from loco to loco.  And there is no simple speed change parameter in DC, like there is with DCC.

So, I would rather not introduce a whole new motor to the group.  This unit does run well with the others, although it runs really hot.

I'll try cleaning it first, using tooth picks and naphtha.  If it runs cool afterward, with no sparking, I still want to think about pulling the brushes, because there is a lot of black stuff in there.  I'll get back on TRW before I do anything with the brushes, though.