Author Topic: The NKP 1000 Series Caboose build thread  (Read 1698 times)

0 Members and 1 Guest are viewing this topic.

peteski

  • Crew
  • *
  • Posts: 35440
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6696
    • Coming (not so) soon...
Re: The NKP 1000 Series Caboose build thread
« Reply #30 on: September 02, 2026, 10:11:04 AM »
0
Excellent info Bob.  That Panel Liner is exactly that: A type of a wash/stain. I also have recently started playing around with it.  It comes with multiple colors. Black is good for deepening locmotive grills, but for surface details I think the other, less stark colors like brown or gray work better for a realistic look.  Going by the smell, those are some sort of oil-based stains so the solvent might affect certain paints used on the model.
. . . 42 . . .

Lemosteam

  • Crew
  • *
  • Posts: 6469
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5029
Re: The NKP 1000 Series Caboose build thread
« Reply #31 on: September 03, 2026, 05:53:03 PM »
0
Oops.
John "Lemosteam" LeMerise

robert3985

  • Crew
  • *
  • Posts: 3602
  • Respect: +2000
Re: The NKP 1000 Series Caboose build thread
« Reply #32 on: September 04, 2026, 04:02:43 AM »
+1

The ends can be flattened if desired, but keep in mind that slight angles angles are at play in its installed position.




I find your work to be exceptional and it inspires me to get to work on my UP, SP and WP cabooses I've had floating around in my head for years.

I've kit-bashed a few UP cabooses and like yours here, they all have smokejack support wires, and I've tried various methods of representing these very fine wires in a way that both looks good and are durable.  Additionally, I don't want them to eventually sag or get bent, which is a problem with very fine, whisker-thin wires of various compositions.

I noticed that on your smokejack, you're using grossly oversized bent wire to represent these supports so, I thought I'd offer a suggestion and a photo or two of what I use and how I do it.

The hardware for my N-scale smokejack support wire is 000000 (6-ought) non-sterile woven black suture silk, which is a bit of a PITA to find, but I bought mine years ago on a wooden spool to represent rat-lines on my 1/8" scale 1800's scratchbuilt sailing ship models since it doesn't fray, ties very well as it's designed to do, and is quite robust strength wise.

I've tried fine stainless wire, ultra-fine Titanium wire, heated & stretched Styrene sprue, and none of them came close to working as well nor as easily as the 6-ought black silk suture.  The wires bend and/or come unglued, the stretched sprue breaks...silk suture doesn't need paint (adds thickness), is stretchy enough to that it never sags, ties in a knot on one end to act as a "keeper", not fitting through the 0.007" hole that I drill for it, threads easily through the same holes in the smokejack and down into the receiving hole on the car body roof, where I pull it tight, put a dab of thick CA on it on the inside of the car body, apply a bit of Accelerator (or nowadays, shine a UV flashlight on it), wait a few seconds for the CA to cure, do the same thing to the knot in the other mounting hole, then snip the excess suture off.

Photo (1) - SP C-30-1 Caboose by MTL, Fine N Scale, FVM and me...note the smokejack support wires... 


Smokejacks by UP put the support wire over the top which is also easy to do with 6-ought silk suture.

Photo (2) - UP CA-4 superdetailing project with over-the-top support wire...close up showing complete absence of any fraying in the woven silk suture:


I've had the above project uncompleted for over 9 years...no sagging, no drying out and fraying.

Since I'm obsessed with getting cabooses "right", solving the smokejack support wire problem is something I thought I'd pass along in this thread because of the excellent work being done here.

Cheerio!
Bob Gilmore

Lemosteam

  • Crew
  • *
  • Posts: 6469
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5029
Re: The NKP 1000 Series Caboose build thread
« Reply #33 on: September 04, 2026, 08:16:48 AM »
+1
Nice Robert.

The proto supports on this caboose are actually flat strip steel (I have the drawings).  I think it would be easy to add some holes in the roof and use some fine EZ line. The smoke jack has a small flat hole in it that would allow the line to slide through, then adding a dab of CA into said hole.  Leave some extra length to pull through two holes in the separate roof would allow for a nice stretch and glue only on the inside of the roof. I will try this on later posts here.

Not sure if you have seen this but there is also very fine ship building wire available now: https://hobbyisthaven.com/en-in/products/0-10mm-memory-metal-super-fine-rigging?_pos=1&_sid=fc91c8059&_ss=r&variant=52790936469793


« Last Edit: September 04, 2026, 11:11:18 AM by Lemosteam »
John "Lemosteam" LeMerise

Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: The NKP 1000 Series Caboose build thread
« Reply #34 on: September 04, 2026, 11:05:05 AM »
+1
I'm as impressed with the bending/cutting jig as with the model!  Ingenious stuff.

Lemosteam

  • Crew
  • *
  • Posts: 6469
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5029
Re: The NKP 1000 Series Caboose build thread
« Reply #35 on: November 04, 2026, 07:11:03 PM »
+9
The PPD etches finally came this week and the model above was printed with the holes that the brass parts would use. I need to tweak the end platform holes just a bit, as the stainless steel etches required a thicker material.

That said I was able to use the parts for the following pictures. I prefer to clear the holes before installing the grabs, which is what I have done for this test.

Straight on end platform view. John and I decided to make the end railings and ladders from Stainless. The rest is brass, and are quite soft.



The cupola roof grabs are brass using grooves on either side of the corner pin to fold into the right angle. These dropped right into their respective holes as designed.



3/4 view from the bottom, showing the upper and lower end wall grabs, end beam grabs, and the distinctive curved sidewall corner grab. The bending and gage grooves help to form it. But the AAA battery diameter did the heavy bending for that grab.



The rear view from the top, showing the roofwalk grab and an old brass brake wheel. I will add the printed version on the next test build.



Overall I am pleased with the parts and their installation. The fret is decent with respect to removing the parts.
John "Lemosteam" LeMerise