Author Topic: East Norwood, OH in Z Scale  (Read 24342 times)

0 Members and 1 Guest are viewing this topic.

Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: East Norwood, OH in Z Scale
« Reply #150 on: September 03, 2026, 06:28:37 PM »
+2
Adventures in 1:220 limestone gravel..

I mixed up a batch of sanded grout with grays and a little brown and applied it.  To the naked eye it looks ok.  To the camera, it looks more lumpy and not consolidated, and also shows "crystals", ie the facets on the sand. 



I thought about what makes the real limestone crushed rock pack down better--more fines.  Gray weathering pigment is fine.. so I went over the whole area with a dose of gray pigment and rubbed it in a bit.  This yields a good look, I think.  It fills in space in the rock like fines, and also tones down the sparkles. 

I added some scenic cement to a section to see what it did, and sprayed the other half with matte clear--both darkened the pigments.  The section with pigment alone looks best and is permanent enough (I'll see how it looks after the cement and clear has fully dried);  In any case, I tested the pigment alone section with a vacuum and it stayed in place.


robert3985

  • Crew
  • *
  • Posts: 3600
  • Respect: +2000
Re: East Norwood, OH in Z Scale
« Reply #151 on: September 03, 2026, 06:41:38 PM »
+1
If you're particular about how your ballast looks, both texture and color, from hard experience, I would make sure I ballasted a small test piece of track before settling on either a texture or color.

In my experience on customer's layouts/modules ofttimes the dry color/texture doesn't even come close to what the ballast looks like after it's been glued down and allowed to dry using the normal soaking with ballast glue method.

Also, the shiny rock surfaces will be less if your adhesive you mix with water is matte.  I find that Mod-Podge Matte works very well without gloss (like white glue) and without white deposits (like artist's Matte Medium sometimes does).

Cheerio!
Bob Gilmore

Chris333

  • Crew
  • *
  • Posts: 19707
  • Respect: +6987
Re: East Norwood, OH in Z Scale
« Reply #152 on: September 03, 2026, 07:33:52 PM »
0
Back in my Z scale days  :trollface

I bought a micron filter screen to sift ballast to about 2 z scale inches.

Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: East Norwood, OH in Z Scale
« Reply #153 on: September 04, 2026, 10:50:40 AM »
+2
If you're particular about how your ballast looks, both texture and color, from hard experience, I would make sure I ballasted a small test piece of track before settling on either a texture or color.

In my experience on customer's layouts/modules ofttimes the dry color/texture doesn't even come close to what the ballast looks like after it's been glued down and allowed to dry using the normal soaking with ballast glue method.

Also, the shiny rock surfaces will be less if your adhesive you mix with water is matte.  I find that Mod-Podge Matte works very well without gloss (like white glue) and without white deposits (like artist's Matte Medium sometimes does).

Cheerio!
Bob Gilmore

Yep Bob, that's exactly what this is--a bit of ballasted test track.   Clearly there's a color change visible on the ballast and this section of "crushed stone" when either adhesive (WS scenic cement) or matte spray (dullcote) is applied.  Dried, they don't look much different than wet (see below).

Chris, I screen N scale ballast to get both the fines and too-large chunks out.  The dust from the 100-mesh could probably be used here, but was pitched when I made my batches for the layout.  The weathering powder seems to do the job though.  I'm pretty happy with this look, plus it'll get some additional weathering:
 










Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: East Norwood, OH in Z Scale
« Reply #154 on: September 07, 2026, 01:49:22 PM »
+3
McCullough Yard is ballasted.  I made "place holders" for the sand tower and it's support. 



We shall see how the fine rock ends up looking when dry, then add the weathering powder (Bragdon Ent. "ash" btw) if needed.



The backdrop will be next.  And I should also be able to "JRTFM" once I give the track a decent cleaning!     




Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: East Norwood, OH in Z Scale
« Reply #155 on: September 10, 2026, 05:44:15 PM »
+5
And voila, with some Bragdon weathering powders I think it turned out ok--not too grainy, matte, and clearly smoother/compacted rock vs. ballast: 


Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: East Norwood, OH in Z Scale
« Reply #156 on: September 15, 2026, 12:37:58 PM »
+4
The remaining backdrops have been installed and structures placed where they'll be.  All the structures can be removed for additional updates or weathering--or just to make working on the area around them easier.

First, here's an aerial from Google Maps of the prototype area modeled.  Obviously a lot of compression was employed, but I'm just trying to give the overall impression.


Going west-to-east: here's Highland Ave crossing.  The small structure will represent Queen City Clay or maybe Motor Boat Storage (?)-- I could 3D print some boats and put in the warehouse which would be a bit more interesting than a clay warehouse;  The larger structure on the left is the Rumpke/Dalton Adding Machine building done from an Archistories kit.  I'm planning to install working flashers on the crossing and there'll be a squealer on the sharp curve west of the crossing.


Here's an overview of McCullough Yard with the engine facility and sand tower all ballasted with backdrop.  I cheated a bit in photo software to hide seams in the sky which I hope to do in real life with some putty and airbrushing or chalks. 


A close up of the yard throat.  I really like how the ballast vs gravel road textures worked out.


On the east end of the yard, there's a mirror on the backdrop to give the impression of depth.  Ignore the giant iPhone!   



« Last Edit: September 15, 2026, 12:56:28 PM by Jesse6669 »

Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: East Norwood, OH in Z Scale
« Reply #157 on: September 23, 2026, 02:30:25 PM »
+3
I took a crack at making the Motor Boat Garage (a real business there on Highland Ave).  The structure was a leftover ancillary building from the Archistories engine house kit that I didn't want to include--so it goes to good use.  The signage came from their website, printed on presentation paper.  The boat is a 3D printed Chris Craft Coho, wrapped to look like it's shrink-wrapped in storage using teflon tape.  I might take another crack at it, teflon tape is tough to work with but I think it looks ok for a first pass.  (I'm gonna get a roll of 1" teflon tape and try that..the stuff I was using was 1/2").  Some cribbing will be put under it.  Maybe I will do some other boats the same way. 



Gonna have to get MOW to clear up those overgrown weeds on the yard lead!
« Last Edit: September 25, 2026, 03:36:33 PM by Jesse6669 »

Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: East Norwood, OH in Z Scale
« Reply #158 on: November 16, 2026, 07:44:03 PM »
+4
Here's a quick update on recent progress on East Norwood.

I've been working on the Highland Ave. crossing, which necessitates a crossing signal.  I have been discussing that in the 3D printing thread.  Suffice to say the design of the signal, electronics for the flashers, and the sound for the signal are in hand and tested.  I've done several test builds of the signal itself to get the design right and just need to do the final version.  I contemplated having the arm go up and down--using a really thin threaded shaft through a servo mechanism, but decided to save that for another time.  The signal on the far side of the tracks will just be a paper cut-out, that is scaled down to fit the perspective.

In the meantime, I needed to get the road and surrounding scenery up to par.  It's not 100% done but we're nearly there.  The road is just sheet styrene, painted with gray primer then darkened with thinned matte black.  I masked the lines with Tamiya tape and mixed up some orangy-yellow and sponged it on.  The sidewalks are from Whistle Stop Models.  They're good and I had no issues.  I probably could've just printed them but I save some trouble by picking them up with the sand tower kit.  They were painted Tamiya buff.  Then the whole lot got some weathering with grimy black powder. 


Here's the actual crossing I'm trying to capture: 


Oddly, there are not "RxR" painted on the pavement--this made my job a bit easier.  Still to add are the xing signal(s) obviously, power lines, more trees, etc.   
« Last Edit: November 16, 2026, 07:47:04 PM by Jesse6669 »

Lemosteam

  • Crew
  • *
  • Posts: 6467
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5029
Re: East Norwood, OH in Z Scale
« Reply #159 on: November 17, 2026, 05:40:08 AM »
+1




This is simply the best layout to background transition I have ever seen. Period.  Other than your crossing signal, I wouldn't change a thing.  It is very well balanced and starkly rural-perfect.  I would not hide that newly built outbuilding with any trees.  Even the seams are non offensive- maybe one or two tall but not wide ones in front of the right seam would seal the deal for me.

Beautiful.
John "Lemosteam" LeMerise

Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: East Norwood, OH in Z Scale
« Reply #160 on: Yesterday at 02:35:53 PM »
+1
There is a final bit of "blank canvas" to be worked on, the area between Beech Street where Rumpke is located and GK Tower.   I debated just putting in a field or some negative space but the prototype offers some suggestions... 


The old freight house was used as a crew office in later years and for MOW/Signals (currently). 


In researching this project I came across this rare photo, which I believe was taken in the early 1900s.  The freight house section was demolished but the tower and far end of the depot remained as GK Tower (and is modeled as it was prior to burning down in the 90s).  It matches up with the later pic.  There was a passenger depot across from the tower/freight house in those days.


The old freight house/crew office was boarded up in the 80s.  I think this is how I'll model it.


I was thinking I might put a compressed Forest Converting Co. just behind the crew office might work but now I'm leaning against this.. it'd be getting really crowded.