Author Topic: Replacement trucks and wheelsets  (Read 750 times)

0 Members and 1 Guest are viewing this topic.

Lemosteam

  • Crew
  • *
  • Posts: 6469
  • Gender: Male
  • PRR, The Standard Railroad of my World
  • Respect: +5029
Re: Replacement trucks and wheelsets
« Reply #15 on: November 17, 2026, 05:27:27 AM »
+1
I have not wheelset swapped that many cars, but I have had issues with wheels popping off of the isolator side on FVM sets even before I opened the package.  to top it off, it is a PITA to get them back on without wobble, so two or three lost wheelsets per package. With ESM however, I have not had a single issue like that.

Just my small personal experience.
John "Lemosteam" LeMerise

samusi01

  • Crew
  • *
  • Posts: 756
  • Respect: +987
Re: Replacement trucks and wheelsets
« Reply #16 on: November 17, 2026, 11:20:13 AM »
0
My track record with ESM wheelsets isn't quite as good as @Lemosteam (I've had one single wheelset have a wheel popped off) but that's not bad for the sheer number of ESM wheelsets floating around on the fleet. Standardized on them a few years back and have not regretted it one bit. Tangent also has wheelsets that are quite nice, and Jackson Railcar (Midwest Model Railroad) have some very free-rolling trucks but I don't recall if they offer wheelsets only yet.

SAH

  • Crew
  • *
  • Posts: 1307
  • Respect: +1948
Re: Replacement trucks and wheelsets
« Reply #17 on: November 17, 2026, 03:07:04 PM »
0
Regarding crud build-up:  Consider how far your rolling stock will move.   Miles upon miles at a club or modular set up vs. 30 feet every year or so on a home layout.  Plastic or metal?  It does not matter.

Appearance is different matter.  How many close-up photos will you take of your equipment?  Open frame cars (tank cars and hoppers primarily) look much better with thinner profile metal wheels.  House cars?  Not quite the bang for your buck.  At layout viewing distance (12" is my standard) most people do not notice the difference between plastic / metal wheel sets.

I've had the same issue Lemosteam did with FVM.  No problems with IM.  I have no experience with ESM but will likely order them when my current mongrel stock runs low.  (I have a little bit of just about everything ever made.  Sometimes those oddballs turn out to be a problem solver.)

The bottom line for my situation:  Use good quality plastic or metal wheel sets.  It does not matter from an operations standpoint IF the truck axle length requirement matches the replacement wheel axle length.  You are asking for trouble if you deviate.

Steve Holzheimer
Lakewood, OH
Modeling the AC&Y Spur 4 Serving the Tire Industry

Chris333

  • Crew
  • *
  • Posts: 19710
  • Respect: +6987
Re: Replacement trucks and wheelsets
« Reply #18 on: November 17, 2026, 03:26:40 PM »
0
Just imagine they were $19 bucks for 4 axles from NWSL.

robert3985

  • Crew
  • *
  • Posts: 3602
  • Respect: +2000
Re: Replacement trucks and wheelsets
« Reply #19 on: November 17, 2026, 04:37:15 PM »
+1
Just imagine they were $19 bucks for 4 axles from NWSL.

Yeah.  I don't have to imagine.  I have several of those old NWSL wheelsets I bought way back in the mid 1980's...and not nearly as good-looking as what's currently available for much much less...

Cheerio!
Bob Gilmore