Author Topic: Looking for dummy knuckle coupler that has long shank and is underslung  (Read 583 times)

0 Members and 1 Guest are viewing this topic.

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
The Tomix track cleaning car I am converting has old rapido couplers that I need to replace with something that is compatible with most knuckle couplers.

I swapped in a dummy knuckle coupler with a long shank, which is the necessary length to clear the car end.  But, it is too low to stay coupled with a Micro Trains equipped car that meets NMRA height specs.

I have short shank versions of these dummy types that are underslung, and would be the necessary height, but those are too short for the Tomix car.

So, I am asking here if anybody knows of a long shank version that is underslung.

chessie system fan

  • Crew
  • *
  • Posts: 1534
  • Gender: Male
  • Respect: +1402
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #1 on: November 14, 2026, 10:01:08 PM »
0
Micro Trains 89' flat truck-mounted couplers?  If those don't work, this seems complicated enough of a search that if it were me, I would just make a rapido coupler transition car. 
Aaron Bearden

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #2 on: November 14, 2026, 10:38:53 PM »
0
The Tomix trucks are pretty much unique to this particular car.  They are all-wheel pickup with coil springs transmitting the current to exposed pieces of pseudo frame.  So, swapping trucks is not an option.

And going to body mounts is not something I want to do, because the decoder is right where the coupler box screw would enter the car body.

I am pondering making my own underslung couplers by cutting the knuckle off one and the T-end off another and then gluing the shanks together vertically to get the underslung effect.  If I do that, I will probably drill in some reinforcing pins to keep the shanks from pulling apart under shear.

But, I'm old with a to-do list that already exceeds my life expectancy, so I would like to find an easier, quicker way.

peteski

  • Crew
  • *
  • Posts: 35444
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6698
    • Coming (not so) soon...
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #3 on: November 14, 2026, 11:39:32 PM »
0
How about the FVM (ex Red Cabbose?) t-shank dummy knuckle couplers? 


Unfortunately FVM is out of stock, but maybe some hobby shops still have some in stock?
. . . 42 . . .

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #4 on: November 15, 2026, 11:25:09 AM »
0
Peteski, That is essentially what I am using, already. 

The problem is that they need to be underslung to get the coupler to the correct height above the rails on the Tomix vacuum car trucks. 

The ones I am using I think came in "Bachmann" packaging, 2 pairs each of short, medium and long shanks.  They look the same as the Fox Valley and other versions, so I think they all probably came out of the same molds in China and got distributed by different vendors.

I don't remember ever seeing any underslung versions with long shanks.  That is why I am checking with the memories of other TRW members to see if they even exist.  If not, then I guess I will be cobbling together my own underslung version of the long shank.  Unfortunately, that takes twice as many of my dwindling cache of these long shank dummies, because I need 2 straight shanks to make one underslung shank.


nkalanaga

  • Crew
  • *
  • Posts: 10611
  • Respect: +1776
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #5 on: November 15, 2026, 04:53:41 PM »
0
If you're up to soldering, you could make new shanks from brass, whatever length you need, then attach the knuckles to them.  It wouldn't be complicated, just a two-piece brass sheet/bar T.  If you can find a piece of brass the size of the cross piece, you could make the shank of brass wire, with a hole drilled in the bar, then bend the wire to fit a hole in the knuckle.  One solder joint and some glue.
N Kalanaga
Be well

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #6 on: November 16, 2026, 11:10:08 AM »
0
Last night I cobbled together an underslung dummy long-shank.  It works fine on my home test loop.  The real torture test will come this Wednesday at the Club.

While looking through my cache of coupler stuff, I realized that the Bachmann package of short, medium and long dummies has the medium length with a configuration that is different from the shorts and longs.  It does not have a T on the box end of the shank, just a pivot hole.  So, I had no use for them and had forgotten about that.  By using a medium shank together with a long shank, I am only using up one long shank, which I would need to convert a car anyway (on one end).

So, what I did was cut the coupler off the end of a long shank, file off the step in the long shank to make it flat on top, cut off enough of the non-coupler end of the medium shank, and glued the medium shank to the top of the long shank.  That gave me the underslung effect I need.

There is some futzing around to get the long shank thickness needed to make the finished coupler height match the gauge, but the epoxy fills in the gap so long as things are a bit too thin instead of a bit to thick.

These dummy couplers are big enough in their vertical dimension that their tops are above the car bottom surface when the coupler face is centered on the MTL height gauge.  So it is necessary to make sure that the combined coupler shank is long enough to get the coupler far enough out to allow for swing without hitting the car end.  Clearance under the car for the combined shank is adequate.

Lining up the parts to glue them was the challenge.  I used double sided tape to hold each of the parts, separately - the long shank on a board and the medium shank on a piece of scrap metal that was the right thickness to raise the coupler height the desired amount when resting on that board. (That turns out to be about  0.045".)  The two parts were each set at the edges of their respective trips of double sided tap.  So, I could check alignment of the two part, then slide the top part away to apply a tiny dab of epoxy, then slide them together again and make sure the alignment is correct.  Being able to handle the board and metal "handles" instead of using tweezers to align the tiny parts is what makes this possible for me.  I used slow setting epoxy, so there is no "grabbing" while still trying to achieve the proper alignment.


peteski

  • Crew
  • *
  • Posts: 35444
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6698
    • Coming (not so) soon...
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #7 on: November 16, 2026, 12:59:58 PM »
0
Good solution. I sure hope the epoxy alone holds on this slippery plastic.
. . . 42 . . .

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #8 on: November 16, 2026, 06:18:56 PM »
0
The epoxy I used is something that I got acquainted with during my sailboat years.  It is called "G/Flex".  It is thickened, so will stay where it is put while not yet hardened.  I have used it to stick stainless to plexiglass for a hinged instrument panel cover that lived outdoors for 20 years, with repeated opening and closing, sunshine, freeze/thaw, etc.  That boat is now sold, but I still have the test piece in my shop, and still can't pull that apart.  This epoxy does not get brittle.

So, I expect it to hold on this plastic.  However, I got interrupted and forgot to degrease and sand the medium shank side of the glue joint.  SO, if it is going to fail, I think that is where it will come apart. 

I am pretty confident that it will hold if both parts are roughed and degreased.

I used the same stuff to fix a couple of Peco turnout throw bars, gluing the plastic to a brass part.  That has held against the throw mechanism tension, so far.  (Apparently, the original throw bar plastic material failed on both at a hole near the end of those throw bars when somebody (UN)adjusted the servos to put a lot if tension on that plastic.)

nkalanaga

  • Crew
  • *
  • Posts: 10611
  • Respect: +1776
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #9 on: November 17, 2026, 01:27:36 AM »
+1
If you want to make sure it will stay together, drill a hole through both pieces, and stick a piece of wire in it.  Between the epoxy and the wire it shouldn't ever come apart.
N Kalanaga
Be well

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #10 on: November 17, 2026, 05:35:38 PM »
+1
I was originally thinking I would use a wire.  But, the shanks are really narrow. 

I have made one, which will get pulled around a layout with notoriously bad track for a while tomorrow at the club.  If it comes apart, I will use wire to repair it and to make the other 2 that I need.  Frankly, tugging on the composite coupler with my fingers makes me think I will not need the wire.

I'll post the result of tomorrow's torture test on Thursday.

wm3798

  • Crew
  • *
  • Posts: 16594
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7527
    • Western Maryland Railway Western Lines
Re: Looking for dummy knuckle coupler that has long shank and is underslung
« Reply #11 on: November 18, 2026, 07:08:42 PM »
0
You're still involved in DelMarVa , correct?  Off topic a bit, but who decided to install a highway around the layout?  That can't be good for the railroad's business, but then again, none of the trucks actually move.

Not a good look, IMHO.
Lee
DMVMRR 1994-2003
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
+1
Well, that test didn't go as expected.  The coupler didn't fail, but the vacuum locked up in about 6 feet of track sucking. 

Turns out it picked up a lot of grit (loose ballast?), and that jammed the rotor in its housing.  I'll put more about that in the other thread about doing the decoder install. 

I had taken Peteski's advice about leaving the current limiting gizmo in the circuit, but wiring it so that it was on the decoder output to the motor instead of being on the input from the track.  The idea was to guard against motor burnout if the rotor locked.  Glad I took the advice, even though I thought the rotor locking would be a rare event.  It never did that at home, but this club layout is a challenge.

Wm3798, yes I am working on the Delmarva Model Railroad Club N scale DCC layout.  I did not join the club until after that highway was put in.  I agree it was a bad choice, for many reasons.  Elmer wanted me to make an overlay for it so that it would not look so plain faced, which led me to find that the clearance on the mainline was so tight in one place that it barely cleared a lot of cars, and did not clear some double stacks.  I did fill the obvious cracks and gouges and repainted it to make it look less embarrassing for our Open House events, but it is going to need some serious Dremeling on it "supports" to get enough clearance for even a very thin overlay. 

Sorry you moved out of the area about the time I joined.  Please stop by for a visit if you ever go to Ocean City.