Author Topic: Replacement trucks and wheelsets  (Read 748 times)

0 Members and 1 Guest are viewing this topic.

Bob

  • Crew
  • *
  • Posts: 472
  • Gender: Male
  • Respect: +623
Replacement trucks and wheelsets
« on: November 14, 2026, 08:00:12 PM »
0
Hi everyone,

I need to replace some trucks and wheel sets on some of my rolling stock - I am strictly modern era.  Anyone have a favorite brand?  I am sure there is a thread about this some place on TRW, but darn if I can find it.  THanks for the advice!

Iain

  • Crew
  • *
  • Posts: 4909
  • Gender: Female
  • Na sgrìobhaidh a Iain
  • Respect: +849
    • The Best Puppers
Re: Replacement trucks and wheelsets
« Reply #1 on: November 14, 2026, 08:30:35 PM »
+1
Well, the nicest wheelsets are from Eastern Seaboard Models.  Keep in mind the axle length to fit your truck.

As far as trucks, there's a variety, and you'll want to pick what best matches your prototype.
I like ducks



OrangeAnon

  • Crew
  • *
  • Posts: 61
  • Gender: Female
  • Respect: +64
Re: Replacement trucks and wheelsets
« Reply #2 on: November 14, 2026, 08:33:19 PM »
+1
I'll second the ESM wheels recommendation. They're all I want to buy anymore.
Alexis W.

PanAmShay

  • Crew
  • *
  • Posts: 90
  • Respect: +39
Re: Replacement trucks and wheelsets
« Reply #3 on: November 14, 2026, 08:53:08 PM »
0
It was suggested to me that wide/standard tread metal wheels are more forgiving than the find tread options, r.e. wheels dropping into turnouts, etc.  Any recommendations on standard tread offerings?  Scale Trains told me they will have new wheels coming out under the Rivet Counter brand soon.

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Replacement trucks and wheelsets
« Reply #4 on: November 14, 2026, 10:29:45 PM »
+2
There are so many reasons and preferences for replacing trucks and wheel sets that it would help if Bob told us why he is replacing some trucks and wheels.  Is he missing parts (maybe couplers or wheels), or do some not roll freely any more, or is he changing over to metal wheels, or is he trying to adjust car heights, or  . . . ?

I get to do all of those things for club cars in need, but am not trying to standardize the club's rolling stock - I just need it to roll freely and couple reliably.  So, I often end up swapping in Micro Trains trucks for Atlas, Bachman, etc, when those don't roll freely enough.  And Micro Trains trucks with Micro Trains plastic wheels do roll a lot more freely than the other brands with plastic wheels.

When swapping trucks, it is important to look at side-play on the bolster pin.  I often need a new pin with a different diameter for the new truck hole, but the same diameter for the bolster hole, because it isn't changing.  Micro Trains made a variety of bolster pins to allow putting their trucks on just about any other manufacturer's bolster.

And sometimes I swap metal wheels for plastic wheels because those do roll better.  I find that ESM rolls most freely - BLMA and Fox Valley are a close second.  Those wheels are machined metal.  Atlas offered some metal wheels that were sintered instead of machined, and those do not roll freely enough for my tastes.  Micro Trains plastic rolls better than sintered metal.

But, it is important to match the axle length pretty closely when doing wheel set swaps.  Putting in a metal wheel with an axle that is too long will result in more rolling resistance, while putting in an axle that is too short can result in the wheels coming out of the trucks during operation.  ESM now makes axles at 0.540" (Micro Trains length) and 0.553" (Atlas length), but there are several other lengths, including 0.563", 0.568", 0.572" and 0.578", which Fox Valley makes.  I find that I need a caliper to do wheel swaps correctly.

And, there are some odd circumstances where I have actually taken good metal wheels out of some cars and replaced them with old Micro Trains "pizza cutter" wheels to address a track problem on the club layout.  (A Peco turnout guard rail was so worn that it allowed a wheel set to pick the frog if the other wheel dropped before reaching the frog, and those pizza cutter flanges stopped the wheel dropping.  That guard rail has since been replaced, but the pizza cutters got us through 8 days of open house.)

So, this is just my long way of saying that our recommendations will probably depend on what the OP is really trying to accomplish.
 

« Last Edit: November 15, 2026, 11:14:35 AM by Maletrain »

Bob

  • Crew
  • *
  • Posts: 472
  • Gender: Male
  • Respect: +623
Re: Replacement trucks and wheelsets
« Reply #5 on: November 15, 2026, 08:20:29 AM »
0
Thanks for all of the information!  I'ld like to move to metal wheelsets, and as for trucks it is for mostly replacing a relatively small number that have some kind of issue with them rather than whole-sale replacement.

shawnfinley@att.net

  • Posts: 15
  • Respect: +4
Re: Replacement trucks and wheelsets
« Reply #6 on: November 15, 2026, 08:55:07 AM »
0
Ive been swapping wheel sets to Tangent, which are narrower than Eastern Seaboard wheels on Kato unitrack without any problems

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Replacement trucks and wheelsets
« Reply #7 on: November 15, 2026, 11:12:11 AM »
0
I think Tangent N scale wheels only come in 0.537" axle length.  Same with BLMA.

If realism is an issue, the Fox Valley and Tangent wheel outside faces look more prototypical to me.

Fox Valley also (at least at one time) has 2 different wheel widths, at least for some diameters and axle lengths.

PanAmShay

  • Crew
  • *
  • Posts: 90
  • Respect: +39
Re: Replacement trucks and wheelsets
« Reply #8 on: November 15, 2026, 11:24:13 AM »
0
Any feedback/experience on Intermountain n scale wheels. Goal for me is freer rolling and improved operation.  Less concerned about exact prototypical appearance as long as they don’t stand out

Maletrain

  • Crew
  • *
  • Posts: 4267
  • Respect: +928
Re: Replacement trucks and wheelsets
« Reply #9 on: November 15, 2026, 11:41:20 AM »
0
I don't have any personal experience with Intermountain wheel sets in N scale.  My club HO members like them in HO scale.  I think they only come in one axle length.

Metal wheels that are machined do tend to roll better than even the best rolling plastic wheels, and they don't seem to collect black gunk on their treads as quickly.  (But, the club has received donated rolling stock with metal wheels so thickly covered in gunk that solvent took off what looked like an intact traction tire.)

Another comment about adding metal wheels: they (mostly) come with one wheel solidly attached to a metal axle, and the other wheel is connected to the axle with an insulation ring to electrically isolate it from the axle.  That insulated wheel can slide a bit on the axle, and that can get the wheel set our of gauge.

I check gauge for any metal wheel sets before and after putting them into trucks.  Sometimes a few come from the factory out of gauge.  And, if I am not careful how I apply force to pop them into the trucks, I can push them slightly out of gauge during that process.  My insertion tactic is to first insert the end with the insulator and then make sure that I am pushing on the solidly attached wheel as I try to pry open the truck enough to pop the second end of the axle into its pocket in the truck.  But, others put forces in other places to do the same thing.  So, just keep in mind that you want the force to be applied to the part that won't slip.
« Last Edit: November 15, 2026, 12:13:38 PM by Maletrain »

PanAmShay

  • Crew
  • *
  • Posts: 90
  • Respect: +39
Re: Replacement trucks and wheelsets
« Reply #10 on: November 15, 2026, 12:07:50 PM »
0
@Maletrain, good point about checking gauge both before and after assembly.  I knew of the construction method, but hadn't though to check on new items.  Your suggested install makes sense too.  Thanks!!

peteski

  • Crew
  • *
  • Posts: 35444
  • Gender: Male
  • Honorary Resident Curmudgeon
  • Respect: +6698
    • Coming (not so) soon...
Re: Replacement trucks and wheelsets
« Reply #11 on: November 15, 2026, 12:53:03 PM »
+4
While I don't own a layout, friend of mine had his layout for around 30 years. I have helped in its construction and ongoing maintenance.



It has impeccable track-work using Peco C80 and 55 track and Peco electrofrog turnouts. He has held weekly operating sessions for years, and hosted many special OPS events. Many visiting operators have commented on how smoothly and  trouble-free the layout operates (even commenting that it runs better than many H0 scale layouts).  He has hundreds of boxcars, mostly Atlas and MTL, and great majority run on their original trucks.  Yes, mostly plastic MTL wheels. If there are any metal wheels, it is because the cars came with them. If any conversions were made, he replaced inferior tucks/wheels with MTL trucks.

Despite the current opinions that metal wheels are "better" than plastic, his track record seems to indicate that there are no real problems with plastic wheels, especially MTL brand trucks and wheels.  For many years those were the quality standard no one could match, and they still work very well. Wheels might not have the most realistic appearance, but it seems that if you want reliable operation, that would not be a priority (especially in N sale with modeling populations aging eyesight). :)

The opinion is that the plastic wheel treads attract more crud than metal wheels, but do they really?  I think the crud is just more visible on black plastic than on shiny metal.  I know there is crud on Kato metal wheels when I clean them after running at an NTRAK show. And if the track is kept clean then there isn't much crud to stick to the treads.  I don't recall my friend actually cleaning the plastic wheels on his cars.  Definitely not on his entire set of cars.

Just some observations  . . .
. . . 42 . . .

ATSF_Ron

  • Crew
  • *
  • Posts: 485
  • Respect: +299
Re: Replacement trucks and wheelsets
« Reply #12 on: November 15, 2026, 02:58:21 PM »
0
@PanAmShay, I've had good luck with Intermountain wheelsets.  In particular, I have several of their older freight car kits that came with pretty crappy plastic wheelsets that have been mostly replaced.  Nice free rolling quality and have not had any gauge issues with them.  The only other metal wheelsets I have experience with are the Fox Valleys.  I like those as well.

ATSF_Ron

Bob

  • Crew
  • *
  • Posts: 472
  • Gender: Male
  • Respect: +623
Re: Replacement trucks and wheelsets
« Reply #13 on: November 15, 2026, 03:51:14 PM »
0
I'ld like to thank everyone for replying - TRW is defintely the place to go for good advice!

robert3985

  • Crew
  • *
  • Posts: 3602
  • Respect: +2000
Re: Replacement trucks and wheelsets
« Reply #14 on: November 16, 2026, 11:40:18 PM »
+3
I'm a bit late to the show, but, I am in the process of replacing most of my cars' wheelsets with metal wheelsets...and it's expensive...especially if you've got a couple of thousand cars in your roster.

I agree with Peter ( @peteski ) that I don't notice any difference whatsoever in operation and/or reliability between metal wheelsets and one-piece plastic wheelsets.  I converted all of my Kadee/MTL trucked cars long ago to the original low-profile MTL wheelsets, with really low-profile flanges and they worked GREAT, and looked much better too, even though the treads weren't metallic, it really wasn't that noticeable during operation and just running in circles.

However, from an appearance standpoint and in N-scale model photography, the metal wheelsets look a LOT better...especially narrow-tired wheelsets, and when I go to the effort to superdetail or scratchbuild a car, I use narrow-tread low profile wheelsets..just because they look a whole lot better.

Since my maximum length train is 9' 7.5" long (non-priority freights that get switched on to center sidings to allow priority trains to pass) with my priority trains being maybe a foot longer, I'm not too concerned about rolling resistance since Delrin to Delrin vs Metal to Delrin bearing surfaces don't seem noticeably different with my train lengths, and Delrin tread surfaces vs Brass tread surfaces also (in my experience) have no noticeable difference.

I like and use exclusively FVM narrow-tread (semi-prototypical) wheelsets with various axle lengths.  The two axle lengths I use are .540" and .553" mostly for MT trucks and IMR trucks. 

Since I hand-lay ALL of my turnouts to "tight" clearances, I don't have any problems whatsoever with narrow wheelsets derailing because of too-wide Check-gauge, or too-wide guard rail clearances, which means I don't need any "forgiveness" in my wheelsets because of out-of-gauge turnouts or track.

From an appearance stand-point, I prefer the outer wheel profile of the FVM wheelsets, particularly because of the narrow division between the curved face and the wheel tread.  The inside profiles of FVM wheels are just straight, which isn't prototypical, but, I'm not looking at the insides of the wheelsets at all when they're on cars that are coupled up and running.  If the majority of time I looked at my cars upside down in a foam work cradle, then it might make a difference. I might make an exception for tank cars, which I have a bunch of.

HOWEVER, it's just my preference as ESM metal wheelsets' outer wheel profile is also pretty close to prototype, but with much more/thicker surface at the division between the curved face and the wheel tread than the FVM wheels.  Both are correct.  I looked at photos of prototype wheel faces and both thick and thin divisions between the curved face and tread are visible.  I learned that as the wheels wear, this area of the wheel gets thinner and thinner, with new wheels being thick, old wheels being thin. 

So, it's just personal preference between the appearance of both wheelsets, with a mix of both probably being most prototypical.  However, ESM has a correct inner surface wheel profile if that's important to you.  Also, it appears to me that the narrow-tread FVM wheels tread is thinner than ESM...which is a big plus IMO for FVM wheels.

From an appearance standpoint another good choice is IMR metal wheelsets, which come in both MTL (.537") and IMR (.553") compatible length axles (which includes other truck sideframes also).  I haven't seen these in the flesh, but photos look as if the inner surface is straight, and the outer surface profile is somewhere between the FVM and ESM wheelsets' profiles.  IMR also says their wheelsets are "nickel plated", then say the newest run has a "...dull, blackened appearance to be more realistic without the immediate need for weathering."  When looking at photos, it appears the treads are still bright & shiny...maybe they're referring to only the inner & outer wheel surfaces & not the tread...maybe. IMR also offers a "High Detail Wheels" package of 12 that includes prototypical inside and outside wheel profiles in only 12 packs, but the same price as their plain wheelset 12 packs.

The only drawback that I've had is because the FVM wheelsets, as well as the other brands, are composed of multiple parts, with one wheel having an insulating center, sometimes these either get out of gauge, or disassemble.  In 100 packs, the FVM wheelsets so far have had at least two wheelsets that were disassembled, which I was able to put back together.  Also, when installing into truck sideframes, push on the non-insulated wheel as it is by far sturdier than the insulated wheel.

I'd think that using this caution while assembling is valid for the other brands also.

The other brand that looks good is 36" metal wheelsets from Tangent Scale Models.  I appears they only come in 36" diameter and MTL compatible .537" axle lengths, however, making them inappropriate for the majority of N-scale freight cars from a diameter standpoint.  BUT, if you want good-looking, correct surface profiles inside & outside, 36" wheelsets, these definitely are an excellent option.

Since a lot of us are converting to metal wheelsets for one reason or another, and many of us have large rosters of cars to convert, price is an important aspect to explore.

Since all of these wheelsets aren't available at any single online store, I'll quote the best prices I found online from various sources, which are: Midwest Model RR, N Scale Supply, Scale Trains, Spring Creek Model Trains

(1) - Tangent Scale Models N-scale 36" dia. 0.537" axle length:     $88.18/100    or    $3.53 per car
(2) - Fox Valley Models N-scale 33"/36" dia. 0.540"/0.553" axle lengths:    $75.99/100    or    $3.04 per car
(3) - Eastern Seaboard Models 33"/36" dia. 0.540"/0.553" axle lengths:    $52.00/60    or    $3.47 per car
(4) - Eastern Seaboard Models 28" dia. 0.540" axle length:     $13.82/12    or    $4.61 per car
(5) - Intermountain Railway 33"/36" dia. 0.537"/0.554" axle lengths:     $116.00/100    or    $4.64 per car
(6) - Intermountain Railway 33"/36" dia. 0.537"/0.554" axle lengths - High Detail Wheelsets:     $15.96/12    or    $5.32 per car

If you're not concerned about inside prototype wheel profiles, then FVM wheelsets are significantly cheaper than any of the others.

If you ARE concerned about inside prototype wheel profiles, and are okay with the outside wheel profile representing a newly applied wheel, then ESM 30" and 36" wheelsets are the best buy.

If you want a more worn outside wheel profile and a proper inside wheel surface profile in a 36" wheel, then Tangent Scale Models wheelsets are it...but, they're a few cents per car more than ESM.

If you need 28" wheelsets, then ESM is your only choice only in 12 packs and for $1.10 more per car than the next most expensive 33"/36" wheelsets.

If, for some reason, your LHS only stocks IMR 33"/36" N-scale wheelsets, plan to pay a couple of cents more per car than the expensive ESM 28" wheelsets.

And finally, if you have money to burn and/or IMR "High Detail Wheels" 33"/36" wheelsets are all you can find in your neck of the woods, you'll have some excellent-looking wheelsets, but, for $5.32 per car!!

I am pretty sure there is very little (if any) difference in quality between these brands...just differences in inner & outer wheel profiles and in the tread width.  From a purely operational standpoint the FVM "standard" wheelset is significantly the lowest price (as well as the semi-scale narrow-tread version) and equipping 100 cars with the FVM's will save you $43.00 over the next least expensive ESM's.

Using FVM's instead of IMR 33"/36" "High Detail Wheels" to equip 100 cars, will save you a whopping $228.00!!

Now that you're informed Bob ( @Bob )...and anybody else, now you'll be able to make a more informed metal wheel decision for your N-scale car roster.

Cheerio!
Bob Gilmore