Author Topic: Weekend Update 11/8/26  (Read 2853 times)

0 Members and 1 Guest are viewing this topic.

davefoxx

  • Crew
  • *
  • Posts: 12401
  • Gender: Male
  • TRW Plaid Member
  • Respect: +8804
Re: Weekend Update 11/8/26
« Reply #15 on: November 08, 2026, 12:56:34 AM »
+23
Of the weathering jobs that I have accomplished over the past few weeks, I might be most proud of this one, V&O FA1 No. 232.  By referring to the book, The V&O Story, I tried to match the weathering that Allen McClelland did to his Model Power FA1s on the original V&O layout when the era was set in the 1970s.



It’s certainly not the best weathering on TRW, but at least I won’t be constantly reminded to start weathering my locomotives and rolling stock anymore.   :P



DFF

A Proud HOer
BUY ALL THE TRAINS!
Member of the ACL & SAL RRs and the N&S Ry. Historical Societies

James Costello

  • Crew
  • *
  • Posts: 1963
  • Respect: +553
Re: Weekend Update 11/8/26
« Reply #16 on: November 08, 2026, 04:11:51 AM »
+12
It's been 12 months in the making, but I got some early 90s era JB Hunt 53' Pines trailers completed recently:
  • Trainworx 53' trailer
  • Atlas Pines trailer landing gear (spine car loads so these are lowered positioned)
  • Modified ICC/DOT bumpers
  • Microscale decals








The deadline was to get these sorted prior to the Trainworx release, so that was just in time  :D

These will be the first 3 of many 53' undecorated trailer projects through the shops.
James Costello
Espee into the 90's

VonRyan

  • Crew
  • *
  • Posts: 3117
  • Gender: Male
  • Purveyors of Fine Esoterica
  • Respect: +714
Re: Weekend Update 11/8/26
« Reply #17 on: November 08, 2026, 05:08:00 AM »
+9
I decided to skip sleeping and go down the basement to work on handlaying the rest of the track on my On30 micro layout.

[ Guests cannot view attachments ]

More in the layout thread for it.
Cody W Fisher  —  Wandering soul from a bygone era.

Modeller in Z, Nn3, N, TT, On30

In Memoriam
Bill Kidd
Bill “Rep” Repholz
Erik Seidelmann

SAH

  • Crew
  • *
  • Posts: 1307
  • Respect: +1948
Re: Weekend Update 11/8/26
« Reply #18 on: November 08, 2026, 09:09:02 AM »
+20
I've always regretted not buying the Life Like Ann Arbor FA-2s when they were first offered a hundred or so years ago.  Certainly not for the mechanism, but such a sharp paint scheme.  Two years ago I found a powered one in a pile at Altoona.  Cheap too.  Then I found a couple of dummies on line.  I had a couple of surplus ATL H16-44 chassis on hand.  Slight longer bolster-to-bolster length than the prototype FA-2 but works fine under the LL shell.  So here we are.  My first sound install.  A pilot master made from a Con-Cor PA donor.  New SS steps installed.  Holes drilled for grabs and such.  Grabs and handrails have been fabricated, awaiting a trip to the paint shop.  So far, so good.

Steve Holzheimer
Lakewood, OH
Modeling the AC&Y Spur 4 Serving the Tire Industry

ednadolski

  • Crew
  • *
  • Posts: 5100
  • Respect: +2121
Re: Weekend Update 11/8/26
« Reply #19 on: November 08, 2026, 11:22:50 AM »
+1


Very effective!  Good color choices, creates depth and atmosphere, and the simple composition complements the foreground models without distracting from them.

Ed

Jesse6669

  • Crew
  • *
  • Posts: 1107
  • Respect: +2835
Re: Weekend Update 11/8/26
« Reply #20 on: November 08, 2026, 01:23:38 PM »
+10
I cleaned up the wiring and put my crossing flasher circuitry into a project box and added some connectors.  In getting all the supplies for this I now have accumulated enough electronics gear (project boxes, bread board, jumpers, capacitors, resistors, switches, etc.) to do some other stuff--maybe a bell sound?  This is really my first project other than layout wiring and switches.  I'm no @Sumner but I'm learning and enjoying the process.  I also received the signage decals so I should hopefully have a finished signal built in the next week or so.



I also modified the Train Master shell design and printed some add-on details to specifically model N&W 173.  In my layout world, N&W sent one up to Cincinnati to test in Clare Yard before scrapping it so it can plausibly make an appearance in Norwood..  An Ebay supplier in Japan--probably China--is sending me an additional power truck to test on these since Showcase Miniatures is out of theirs but hopefully not for long.  Anyone have any they'd part with?  It's their model 0018 "Nn3-Z Scale Power Truck".  Alternately--I'll design my own I guess.
 

 
« Last Edit: November 08, 2026, 04:10:00 PM by Jesse6669 »

RockGp40

  • The Pitt
  • Crew
  • *
  • Posts: 1070
  • Gender: Male
  • Respect: +359
Re: Weekend Update 11/8/26
« Reply #21 on: November 08, 2026, 02:39:31 PM »
+11
A random Facebook post two days ago made mention of a model railroad open house near me. Unbeknownst to me, I am living in the presence of greatness with Frank Lagno's Allegheny Central Railroad about 10 minutes from my house. A beautiful yet quick drive was made. Here are some various photos of his well documented HO layout:

Here is a small yard with an even smaller locomotive servicing facility to the left of it (not seen):
[ Guests cannot view attachments ]

I'm a sucker for grain elevators, and the two cars here are destined for Perdue in Salisbury, MD according to the car cards:
[ Guests cannot view attachments ]

And I caught a manifest coming through the fictional town of Keenemont being led by this guy:
[ Guests cannot view attachments ]

This was the second of three engines consisted:
[ Guests cannot view attachments ]
« Last Edit: November 08, 2026, 05:26:47 PM by RockGp40 »
No farms, no food. Support your local farmer's market!

I stand with Israel.

ednadolski

  • Crew
  • *
  • Posts: 5100
  • Respect: +2121
Re: Weekend Update 11/8/26
« Reply #22 on: November 08, 2026, 03:59:40 PM »
+2


Possible thought for that river-meets-the backdrop:   how about a small (Z-scale maybe?) distant model bridge, airbrushed with an oversparay of thinned blue/white 'atmosphere' to create a sense of distance?  Could be most any kind of bridge - girder, truss, stone, .... something to suit the locale.  Could even be a forced perspective or flat.

Just  a-thinkin...


Ed

Dave V

  • Crew
  • *
  • Posts: 12425
  • Gender: Male
  • Foothills Farm Studios -- Dave's Model Railroading
  • Respect: +12075
Re: Weekend Update 11/8/26
« Reply #23 on: November 08, 2026, 04:14:24 PM »
+4
Possible thought for that river-meets-the backdrop:   how about a small (Z-scale maybe?) distant model bridge, airbrushed with an oversparay of thinned blue/white 'atmosphere' to create a sense of distance?  Could be most any kind of bridge - girder, truss, stone, .... something to suit the locale.  Could even be a forced perspective or flat.

Just  a-thinkin...


Ed

That's a great suggestion. However, these are meant to represent real scenes, and there's no downstream bridge from Granville that would otherwise be visible from that angle. The river curves almost 180 degrees to the other side of Lewistown depot before the next bridge is encountered.

Instead I'm working on something like this, that'll then be framed by more 3D trees. The final image would be mirrored so that the river curves to the right.

[ Guests cannot view attachments ]

nickelplate759

  • Crew
  • *
  • Posts: 3887
  • Respect: +1663
Re: Weekend Update 11/8/26
« Reply #24 on: November 08, 2026, 06:03:46 PM »
+8
On a Trading Post thread @chessie system fan asked for more info about a Bachmann 60' hi-cube kitbash  I did years ago.
The car was bashed from two Bachmann 40' high-cubes.  Basically I cut the middle out of one car and spliced the new longer ends onto the other.   My skills and tools at the time were limited, so the splices show in the photos below.  New ends were scratchbuilt from Evergreen styrene.    Paint was Floquil, decals were from Walthers (it was a while ago!).  Underframe (no pictures) was just the Bachmann underframe stretched - nothing close to prototypical.

Here are some pictures.

Side view:



Roof:



Brakewheel end.   Ladders were etched brass, handbrake was from Quality Craft.


« Last Edit: November 08, 2026, 06:07:59 PM by nickelplate759 »
George
NKPH&TS #3628

I'm sorry Dave, I'm afraid I can't do that.

Dave V

  • Crew
  • *
  • Posts: 12425
  • Gender: Male
  • Foothills Farm Studios -- Dave's Model Railroading
  • Respect: +12075
Re: Weekend Update 11/8/26
« Reply #25 on: November 08, 2026, 07:09:32 PM »
+4
Skyboards were a spectacular fail. I was unsuccessful in removing the warp I mentioned in a thread over the summer. I would not recommend CMR skyboards.

I will be trashing these and using 1/8" masonite instead.






brill27mcb

  • Crew
  • *
  • Posts: 239
  • Respect: +84
Re: Weekend Update 11/8/26
« Reply #26 on: November 08, 2026, 07:17:06 PM »
+2
Painting the skyboard on both sides may reduce its tendency to warp.

Rich K.
Tomix / EasyTrolley Modelers' Website
www.trainweb.org/tomix
N-Gauge Model Trolleys and Their History
www.trainweb.org/n-trolleys

Dave V

  • Crew
  • *
  • Posts: 12425
  • Gender: Male
  • Foothills Farm Studios -- Dave's Model Railroading
  • Respect: +12075
Re: Weekend Update 11/8/26
« Reply #27 on: November 08, 2026, 07:52:54 PM »
0
Painting the skyboard on both sides may reduce its tendency to warp.

Rich K.

They are painted on both sides.

Dave V

  • Crew
  • *
  • Posts: 12425
  • Gender: Male
  • Foothills Farm Studios -- Dave's Model Railroading
  • Respect: +12075
Re: Weekend Update 11/8/26
« Reply #28 on: November 08, 2026, 09:03:10 PM »
+10
In model railroading, there are times where things go awry. Sometimes you can save them and pull out a victory. Sometimes, if you're lucky, the initial problem sends you down a path that ends up in a better result than you would otherwise have arrived at. Then...sometimes you find yourself doubling (or tripling down) on a project long since derailed out of dogged stubbornness or the sunk cost fallacy. I've been in this hobby for 44 years in some capacity. I've sh!t the proverbial bed on too many projects to remember.

When I was doing my FAA checkride for my single engine VFR license, I had done all the things. Had done the short field takeoff/landing, the soft field takeoff/landing, the emergency procedures, stall recovery, etc., etc. I was feeling really good, and the FAA rater had been complementing me throughout my flight. So I let my guard down. On approach to Vero Beach to drop off my rater, I was slightly below glideslope and little slow...three reds on the PAPI. So, I added some power, recovered the glideslope, and touched down just beyond the threshold. A perfect landing. Or so I thought.

I was immediately informed that I had failed the checkride. I had to come back in two weeks to take the same rater around the pattern once and demonstrate a normal landing a second time.

Why?

He told me that I should have gone around the second I knew I was too low and slow. Had I gunned the engine and called a go-around, he would have passed me. But his lesson to me was:

"Never try to salvage a good landing from a bad approach."

That stuck with me. Frankly it applies across all aspects of life. And to model railroading.

When I was unsuccessful in removing the warp when these things were unpainted, that should have been the end. But no, I pressed on. Instead of calling a go-around, I stayed on short final, well below glideslope. Four reds on the PAPI. And buried the nose 50 feet short of the threshold.

Fortunately, you can walk away from a model railroad wreck. A couple custom cut pieces of plywood is hardly a plane crash. And it's not destroying a rare brass piece or dropping a Blackstone K-27. It's a weekend of otherwise enjoyable work that unfortunately won't pan out. But I did learn that I really like the choice of colors and the concept of a continuous ridge. So it wasn't a complete waste.

And I live to model another day.
« Last Edit: November 08, 2026, 09:58:15 PM by Dave V »

up1950s

  • Crew
  • *
  • Posts: 9978
  • Gender: Male
  • Respect: +2913
Re: Weekend Update 11/8/26
« Reply #29 on: November 09, 2026, 12:46:23 AM »
0
In model railroading, there are times where things go awry. Sometimes you can save them and pull out a victory. Sometimes, if you're lucky, the initial problem sends you down a path that ends up in a better result than you would otherwise have arrived at. Then...sometimes you find yourself doubling (or tripling down) on a project long since derailed out of dogged stubbornness or the sunk cost fallacy. I've been in this hobby for 44 years in some capacity. I've sh!t the proverbial bed on too many projects to remember.

When I was doing my FAA checkride for my single engine VFR license, I had done all the things. Had done the short field takeoff/landing, the soft field takeoff/landing, the emergency procedures, stall recovery, etc., etc. I was feeling really good, and the FAA rater had been complementing me throughout my flight. So I let my guard down. On approach to Vero Beach to drop off my rater, I was slightly below glideslope and little slow...three reds on the PAPI. So, I added some power, recovered the glideslope, and touched down just beyond the threshold. A perfect landing. Or so I thought.

I was immediately informed that I had failed the checkride. I had to come back in two weeks to take the same rater around the pattern once and demonstrate a normal landing a second time.


Why?

He told me that I should have gone around the second I knew I was too low and slow. Had I gunned the engine and called a go-around, he would have passed me. But his lesson to me was:

"Never try to salvage a good landing from a bad approach."

That stuck with me. Frankly it applies across all aspects of life. And to model railroading.

When I was unsuccessful in removing the warp when these things were unpainted, that should have been the end. But no, I pressed on. Instead of calling a go-around, I stayed on short final, well below glideslope. Four reds on the PAPI. And buried the nose 50 feet short of the threshold.

Fortunately, you can walk away from a model railroad wreck. A couple custom cut pieces of plywood is hardly a plane crash. And it's not destroying a rare brass piece or dropping a Blackstone K-27. It's a weekend of otherwise enjoyable work that unfortunately won't pan out. But I did learn that I really like the choice of colors and the concept of a continuous ridge. So it wasn't a complete waste.

And I live to model another day.

Sounds a touch too overstrict to teach you a lesson . Being that you realized your errant slope , corrected ,  and put her down well within normal landings for the runway length at hand IMO . Then mentioned that which you quoted from him which we all can benefit from . Unless this was your ONLY landing with this guy .


Richie Dost