Author Topic: The Warren Piece  (Read 967 times)

0 Members and 1 Guest are viewing this topic.

randgust

  • Crew
  • *
  • Posts: 3289
  • Respect: +3010
    • Randgust N Scale Kits
Re: The Warren Piece
« Reply #15 on: November 16, 2026, 10:32:43 AM »
+2
OK, the next two steps are relatively complete at the moment......

1)   I got the 'base coat' of painting on the building, mostly because it's next to impossible to paint properly UNDER the roof and behind all those arches once they are in.   I found an acrylic light sand color that is at best, a compromise, as it looks lighter than typical PRR depot buff in every shot I've seen; i.e. not as yellow.   And the lower color is also unsure, I'm going with a brown that is going to have to do.

Where I have to glue on the arch supports - I did not paint, that still shows as red brick, and I'll paint all that when the arch supports are actually on.

2)  The roof is problematic because remember, I only have a front elevation and a floor plan to try to work from.  And, the roof material I'm using (Evergreen styrene) is .040, so its difficult to cut and measure.   So I decided to dummy up the entire roof with posterboard, and use those pieces as patterns to cut the final roof material.   That also proved that I had the width slightly wrong, as the front 'edge to ground' measures 11' on the nose around the entire building, which is critical to get the arch supports later.    That also let me cut all the notches and slots around the pillasters, and then check the length and various dimensions once it was on the building.   That gives a pretty good feel for the roof, I'm satisfied.   All those pieces are just taped together for now, easily cut apart and used for patterns.   





I cut up most of the 'real' roof panels on the top roof last night.   Slow going, but it came out better than the Steelers-Bengals game.

Oh, in case you're wondering, meanwhile, I'm casting up those arches like there is no tomorrow, there's a whole lot of those to make.
« Last Edit: November 16, 2026, 10:35:08 AM by randgust »

wm3798

  • Crew
  • *
  • Posts: 16593
  • Gender: Male
  • I like models. She likes antiques. Perfect!
  • Respect: +7525
    • Western Maryland Railway Western Lines
Re: The Warren Piece
« Reply #16 on: November 17, 2026, 01:38:58 PM »
+1
Construction Nerd here.
You can simulate the flashing between the brick walls and the roof deck with thin strips of masking tape to cover that gap between the surfaces.
Usually metal work would extend about 6 to 8 inches up the brick wall, and get tucked into a horizontal mortar joint around the building.  A strip of Plastruct or Evergreen angle stock might work on the sides, but the oblique angle along the top edge of the long transition will require something a bit more flexible.

You can make out the line of flashing just above that hip on the platform roof in your picture.



Looks to be about 6 or 8" with the peak of the flashing turning down just above the ridge of the roof.  The bottom edge of the flashing would extend OVER the finished roofing...

I have every confidence that you'll have it looking fantastic with or without my penchant for building trivia. :D

Lee
Rockin' It Old School

Lee Weldon www.wmrywesternlines.net

randgust

  • Crew
  • *
  • Posts: 3289
  • Respect: +3010
    • Randgust N Scale Kits
Re: The Warren Piece
« Reply #17 on: November 17, 2026, 03:30:54 PM »
0
One of the bigger headaches I've had is the roofing material.   I came to the conclusion it was a very early galvanized metal standing-seam roofing, mostly by studying some big enlargements I have of the condition prior to demolition.  Hmmmm.   All those seams are not corrugated metal, came later.  PRR liked the stuff.   And it peeled back showing it was sheet metal in the 1980's shots.   The only 'old' shot taken in 1867 is too blurry to guess on material, but the expanded building pre-1910 has the same roof it ended up dying with.

I decided to go to the smallest spacing Evergreen standing seam stuff:  https://evergreenscalemodels.com/collections/040-1-0mm-opaque-white-polystryene-standing-seam-roof

But in the 'fine print' is that the seams are separate .010 x .020 (or smaller) individual seams that fit in the individual cut slots.   Holy %$$#@.   I did discover that thin ACC crawls right down the seam and sets them in after placement, and after painting a test sample, looks just fine.   But there are literally hundreds of individual parts now.   I did not realize that until I got it.

Color is another thing.   Black?  Brown?   Rust?   Yes.  All of that.  it's not copper for sure.  It looks deep rust brown with a lot of black on it, possibly from ages of coal dust and grime, maybe a tar overcoat at some point.   I did a test sample for painting and weathering before I went all-in on this.   I think I'm good.

But that also means I have to paint the roof before putting it on the building, in chunks.   Precisely fitting all parts, then removing to paint and weather, then put on.   I'm looking at the 1920's look here, so I don't lean toward damage at least.   An assembled roof won't fit, and if I'm using chalks to weather, that's an invitation to mess up everything on the walls.

Then that gets me into the real mess of all those arched roof supports and fitting that conglomeration together.  I have to fit the building to the base as those posts between aren't much bigger than a 4x4 at best, they need to be hole-socketed into a brick base at the bottom and glued into the roof at the top.  I'm happy with my castings, but this isn't going to be easy.   

Right now I just need to finish the roof and all those tiny seam pieces.

If you go on FeePay and search "Warren PA train depot" you'll see lots of old colorized postcards in the 1910 era that show various shades of roof, all colorized, and some nice angles of the forest of roof supports I'm faced with.
« Last Edit: November 17, 2026, 03:35:55 PM by randgust »

Chris333

  • Crew
  • *
  • Posts: 19707
  • Respect: +6987
Re: The Warren Piece
« Reply #18 on: November 17, 2026, 04:07:51 PM »
0
I glue those strips to sheet styrene with MEK in a small Testors bottle with the brush in the cap. Lay out the lines in pencil with a square.

Chris333

  • Crew
  • *
  • Posts: 19707
  • Respect: +6987
Re: The Warren Piece
« Reply #19 on: November 17, 2026, 04:24:36 PM »
0
When will we see this?   :lol:

https://www.ebay.com/itm/327215289877

dem34

  • Crew
  • *
  • Posts: 1901
  • Gender: Male
  • Only here to learn through Osmosis
  • Respect: +1457
Re: The Warren Piece
« Reply #20 on: November 17, 2026, 05:53:45 PM »
0
What in the Gorre and Daphetid is that curve in the bottom left
-Al

randgust

  • Crew
  • *
  • Posts: 3289
  • Respect: +3010
    • Randgust N Scale Kits
Re: The Warren Piece
« Reply #21 on: Yesterday at 06:36:04 AM »
0
That's on the far eastern edge of Warren - the "Glade Bridge".   What you see is the trolley track of the Warren Street Railways line to Sheffield, PA, that was over top of the second steel truss bridge over the Allegheny River.   I remember that bridge long after the trolley track was taken off the top.   My Grandmother told me about riding on it via trolley to a balloon raising in the 1915 era.
The track in the foreground is the current Buffalo & Pittsburgh line between Johnsonburg and Erie, PA.   On the other side of the river is the current United Refinery to the left, and the dark building on the right edge is the Allegheny Hotel, alive and well as one of the oldest in the state, ate there last night as the Eagles Club.

That bridge has been replaced as a modern concrete one, although the stone retaining wall for the trolley line remains today.   The other "WTF" was on the north side where the trestle ramp to get on top of the bridge was like 10% grade approach trestle coming up from street elevation resembling a roller coaster light construction.   

The dark blob on the center of the bridge top is a trolley, generally an 8-wheel wooden Brill.   
« Last Edit: Yesterday at 06:40:23 AM by randgust »

Sokramiketes

  • Crew
  • *
  • Posts: 5426
  • Better modeling through peer pressure...
  • Respect: +2196
    • Modutrak
Re: The Warren Piece
« Reply #22 on: Yesterday at 12:22:47 PM »
0
I had a 77' Thunderbird with fog lights just like in the photo  :lol:

With all four wheels on the ground?  Surely not...

#threewheelmotion